r/ACInfinityAdvancegrow

Hi folks,

This is my first grow in the ac infinity 2x2. Before I reach out to their customer support, trying to see if what I did is something easy to fix or obvious to all of you with way more experience than I have. I may have just killed my plant. I happened to walk down to the basement for something else and caught it at 130 degrees.

I’m running an AC infinity 2x2, with their light, vent & circulation fans, and heater. My tent is in my basement and I’ve been doing okay ish without a humidifier- been debating adding that on.

Before today I was running the AI mode. This morning, I switched from AI to advanced automations. Idk if this is normal but on the AI mode, the vent fan and heater were constantly running and seemingly fighting each other (I have my vent fan vented into my heater- is that an issue?). As a result the temps and humidity in my tent were oscillating a good 5-8 degrees every 20-30 minutes, and that didn’t seem great for plant health. I had the same experience setting a priority for temp only, humidity only, or no priority set.

All morning until about 2pm, everything looked great on the advanced automation mode. I set my temp and humidity tolerance range (can’t remember what it’s called in the app but the range you set so your heater doesn’t click on the second it goes off your set temp) and viola! No more constantly on/off heater and vent fan, and my temp/humidity held pretty steady. I thought I was good to go.

But then it looks like a sudden temp drop, my light apparently turned off, and heater went to level 10. I vented the tent, cooled it way down, put it back on AI mode, and stuck a humidifier in there on low to help re balance things (I can manually turn it off and on outside my tent).

Is there something obvious that I did wrong here? If I stay on AI mode, is there any way to tell it to chill tf out and have a bigger range of tolerance so my plant doesn’t experience constant temp whiplash?

Thanks in advance!

Just had to put in for a replacement hydro sensor due to the temperature reading being WAYYY off. Just curious if anyone else has run into an issue with the temp readings? Makes me also wonder if the PH and EC is accurate because the temp sensor is so far off. So far in fact, that I can't even set an offset because it only lets you go up or down by 20degrees and the temp is off by like 50 degrees or more. Water constantly shows 120 or more (or simply will say "HI"). I took a meat thermometer which showed water at 70 degrees while the ac infinity sensor showed over 120.

I have a 5x5 tent with a 6" inline fan and carbon filter. I recently added a Terraform T8 air conditioner. The new a/c made my humidity skyrocket and the VPD tank.

I am in a quandary. Should I upgrade to an 8" exhaust fan and filter ($$$$$), or would a Hydrone humidifier ($$) be sufficient?

I already know how to read so I am looking for replies that come from experience.

Chicken N Waffelz Week 8. Sure am glad I left some smaller buds when defoliating. Turning out frostier than the mains.

does anyone know where i can purchase more cords that connect from the led driver to the lamp. i remotely mounted my drivers next to my 240v flip box but the company only supplied 1 8 foot cord per led driver. it doesn't look like they sell additional ones on the website and it has some proprietary water proof twistlock on the ends. ? i dont seem to have enough cord to reach from my flip box to where i hang my lights in a co2 enriched room. any help would be much appreciated.

Like I'm logging in for the very first time. All hubs gone, all that attached devices gones, all the individual settings and customizations that took me quite a while to fine tune, gone.

Wtf?

Been using this for 3 years within any issues but this update wiped it all out, poof.

Rather than set all this up again, I'm gonna look around and see what else is out there, seems likes a good enough time.

Hope it doesn't happen to anyone else.

Anyone have any good suggestions?

Went wild in the last week and a half and cruising now. Light is at max height in the tent, they get any taller and I may have to do a bit of supercropping.

Anyone else get this message? If I paid $30 -60 maybe it would been ok . But almost its $200 !!

I seen this message and was thinking it shipped because I seen a lot of people got theirs already.. SMH

Hey team, this is my first indoor grow. I don’t have a par meter and have questions regarding my light height. I’m trying to keep the light at least 36” above the canopy as I have a humidifier inside the tent that I don’t want it damaging the light.

I’ve asked google the following question and I’m just curious if these numbers sound accurate to you guys. Thanks

Day 18 flower. Will defoliate lowers on day 21. I’m not out of height yet but it would even out the canopy a bit. Thoughts??

Photos just part of my setup. I have 2 tents. But this one is the one I always have trouble with come summer and flowering. Fyi not first run at all. I run a good ac unit, and it just doesn't do enough for the flowering tent. And I cant think of any other way to get the temps down. I run a medic grow fold 8, which runs a tad hot. I have my inline fans exhausting out the window at full speed. The room is just as cool as the ac unit is set (72°), but the flower tent stays around 80°-84°. I have all my bottom flaps open. I deal with this when summer comes, and I still haven't figured out what I can do. If only I could leave one the side doors on the tent cracked without having light leak issues.

Got a co2 kit plus the new camera ai spectron 7 and a bunch of other goodies

Here's some juicy shots of madd fruit (P.C.G.) grown with the evo 6 by ac infinity. Was using a 315 cmh just before the swap and loved the penetration/efficiency but just wasn't quite getting me to the lb. I was always coming in around 12-14oz. This is the first round with the new light. It seems to be a game changer, it runs cooler and seems like the utilities went down a tad. Excited to see what difference it will make in yield, stay tuned.. less

I feel like I'm missing something simple here but can figure it out myself, hoping to get help.

I have my dehumidifier set to trigger at 53% with a 2% buffer and a 1% transition. However as soon as it hits my trigger point it just screams to max setting of 9, no ramping at all.

Anything in these screenshots tell the story why? Thanks