r/Novritsch

Game day 2 and I am loving my SSX10. I've added an extension to the rear and routed the hpa line to a more comfortable position. Next step, barrel experimentation.

Almost completely stock, using a cheap Hawke 3-9x on a riser, 0.43s at about 360fps.

I was really happy with the accuracy; my first shot of the day was a headshot, and I got a lot of precision kills. Plenty of targets I wouldn't usually have hit cleanly (normally run MWS) but this thing was bang on.

I particularly like how portable and pointable this thing is. I don't want to "snipe" as such, I want to be sneaking forward and hitting the flanks. It was ideal for this, I loved being light and mobile. There were points where I was taking up forward positions and maneuvering around cover with no trouble at all.

Negatives were the line popping out, and I would like a little more consistency, I had rounds veering slightly off target. Wasn't a big deal at the ranges I fought at but I think it'd be frustrating if you're really trying to reach out and touch people.

Next steps are camo and maybe a slimmer HPA tank. But very chuffed!

Just wanted to share my experience with a brand new SSQ4.

Straight out of the box it wouldn't fire at all. I tried five different fully charged gas magazines, the bolt went fully into battery every time, but it only dropped the hammer like it was dry firing. Not a single BB was fired(from me)

I've already contacted Novritsch support and they're currently looking into it. They offered to send me a replacement spring set, but honestly, I don't think I should have to repair a BRAND NEW RIFLE that has never fired a single BB.

I didn't want to start disassembling a brand new rifle, but eventually I found the issue (see photos).

It really makes me wonder how this rifle passed quality control in the first place. Pretty disappointing QC for a rifle that is on the market new and never even fired one shot from the buyer....

Hello everyone, I have an issue with my Ssp1. I've ully cleaned and oiled the gun as per the guide and since then, the slide catch on the barrel or the bolt as per the picture. It's halfway stuck and I have to push on the tip of the barrel to make the slide cycle back.

Any idea on what could be the cause?

Just got my SSQ4 and where my hpa line connects to the gun leaks my air like no tomorrow. The connector on the gun spins freely and looks like maybe a piece is missing but I'm not sure

Not for everyone I know, but my mate asked me to make one for his new SSQ4...so I made 2😂

Field test this sunday. 3d printed in PETG GF.

What do you think? It's a PuffDino paint and a finishing agent. It's more matte than metal, but I like it

Just published these 3D print files for pistol grips for free on Makerworld. They fit my SSX10 nicely and feel really good IMO.

A selection of 5 different textures, from smoother Hex to rough stippling.

Hope this helps someone 👍

https://makerworld.com/models/2996225?appSharePlatform=copy

Buddy of mine Screwed his M4. So I took some of his Parts to my SSR9 to live another Life

Was using my SSP5 in a gameday yesterday, and while shooting the nozzle assembly flew out, and the rear sight flew up. I know this is due to the screw on the rear sight loosening, but how can I stop it from happening? I know threadlock is one suggestion, but I strip everything out and clean it often due to using it once or twice a week, so don’t fancy heating it and reapplying threadlock every time I want to clean it.

Hello everyone. I am pleased to release (for free) the files to print your very own SSX10 upper barrel cover and end cap.

https://makerworld.com/models/2986412?appSharePlatform=copy

The end cap just clips into the end of the lower mlok section covering the ugly green gas valve ( that most of us won't be using.) it also serves as the retention clip for the upper outer barrel cover.

The upper barrel cover must be used with the end cap to hold it in place.

If you like it please drop me a.like or even a boost on Makerworld as it makes a difference to me and costs you nothing 🙏

Very happy to have gotten this. Can’t wait to play with it 😎

Believe should be enough for a milsim day?

Habe gestern meine SAQ4 HPA bekommen. Nachdem ich relativ viel Kritik gehört habe, bin ich extremst positiv überrascht. Ich habe eine Daniel Defense GBBR und finde, dass die Novritsch im Vergleich sehr snappy und direkt ist. Es fühlt sich einfach mega an, damit zu schießen. Außerdem ist sie sehr gut verbaut, hat gute Qualität und nach ein paar Testschüssen im Garten schießt sie extrem präzise. Leider brauchen sie aber endlich eine Lösung, damit der Bolt jedes Mal hinten bleibt beim leeren Magazin.

Wie gefällt euch mein Build?

SSX10 WIP

Ran it completely stock for it's first outing this week but now its time to tweak. Overall a light, compact HPA sniper.

**3D Print elements**

\- Upper barrel cover

\- Hand guard end cap

\- Skeleton pistol grip

\- Fixed stock bracket

\- Skeleton stock bar

\- SI inspired stock end

All printed in PLA + for now as a test. Final will he in PETG GF.

All printed on a used and abused A1 Mini.

**Planned changes**

**Scope need raising a bit (I am a big lad...), bucking and nub swap, maybe a new inner barrel ( needs more testing),stock needs a TPU but pad, folding stock hinge, smaller suppressor and HPA line routing.**

I just want to share my ssr77 dmr setup.

I bought a used SSR9 from a (somewhat) reputable guy. Although having to comply with Germanys regulations he modified it to a dsg and showed me a video proving it shot when he tested it.
After being shipped with GLS in a disassembled state (upper and lower) it doesn’t shoot properly (as seen in the video).
I have tried multiple times to reassemble the gearbox in accordance with the novritsch video but to no avail.
I’m not sure what the issue at hand is due to the gun „cycling“ fine when the spring isnt installed

Attached is the firing demo, the gearbox right after being fired with no parts having been touched (except trigger and anti reverse latch to hold it down so they doesn’t spring out) and the gearbox in a completely disassembled state

I’m not exactly sure if this has to do with some parts being aftermarket but gears, tappet plate, springs and latch seem to be novritsch branded.

Would love if someone could help me fix this myself since there aren’t any novritsch stores in reach