r/SonyFX6 | reddlx

FX6 and UWP-D27 lav issues

I’m having issues with the signal from my transmitters to my receiver dropping out.

I always sync both transmitters to the receiver before recording too.

It’s an intermittent problem, and I could be wrong but I think it’s worse when I have both lavs connected. Saying that, I was only using one yesterday and it was dropping out too.

Any ideas how to resolve this? Also, I’m not a soundy so please try explain it to me in simple terms if you have any ideas.

u/MikeyPikey444 — 12 hours ago

▲ 770 r/SonyFX6+1 crossposts

Split room shot I achieved fully in camera!

Started with a open white walled set which was
turned into the two separate room look.

The project was for a clothing brands campaign but I’ve honestly been itching to do this for so long, let me know what you guys think!

https://www.instagram.com/madefromskin

u/inkstainedcash — 4 days ago

▲ 310 r/SonyFX6+1 crossposts

Tracking shot I did on my FX6

No fancy rig to make this happen, it was just my friends truck following the character while I was in the back holding my camera while it was on a tripod.

I figured i’ll share my instagram if anyone wants to see my other stuff aswell: www.instagram.com/madefromskin

u/inkstainedcash — 5 days ago

▲ 10 r/SonyFX6

12,800 noise

Hi there! New FX6 owner here. What are your best methods for having the lowest noise possible at the second base of 12,800? Should I use internal noise reduction or still avoid it?

Shooting in Cine EI S-log3

reddit.com

u/wheelinforafeelin — 4 days ago

▲ 2 r/SonyFX6

Smallest travel tripod for fx6

Whats the smallest tripod to pair with the fx6? My other camera is the a7siii with a manfrotto befree. Its a really small set up i can travel with easily. Sometimes i need two cameras to travel via public transport.

Notmally I dont need a v-mount. But i do often like to have a monitor with a large NPF.

thanks

reddit.com

u/g_junkin4200 — 7 days ago

▲ 28 r/SonyFX6

3D printable Airtag bracket for FX6 and Tilta battery plate

https://www.thingiverse.com/thing:7375313

I was looking for the optimal place to mount an Apple Airtag on my Sony FX6, and realized there's a perfect Airtag-sized gap under the Tilta Battery Plate. There also just so happens to be two M3 screw holes on the camera body right there as well. So I designed this bracket to hold the Airtag in place in there. Use two M3x10mm screws.
I tested this with both iterations of the V-mount plate (the original design with the integrated DC power cable, and the updated design that powers through the BPU battery slot) and they both work. I haven't tested this with the Gold Mount plate, but hopefully it's the same dimensions.

The camera body and Tilta battery plate are exactly the right dimensions to stop the airtag from moving forward and back. The side walls of the bracket stop the airtag from moving left and right. You can add gaff tape to shim the bracket and adjust how much pressure it puts on the airtag being able to move up and down. I guess that might be useful if you're using the battery plate without screwing it into the Tilta top plate, as I believe there can be a little bit of play inside the BPU slot without the screw. I have it installed on my FX6, and there is no rattling sound; the airtag does not move.

This probably goes without saying, but the bracket will not work without the Tilta battery plate.

u/astropancakes — 8 days ago

▲ 57 r/SonyFX6

The Sony Burano EVF works with the FX6!

Alright this is super cool guys, I've always been curious about it! All the original FX6 EVF functions work as well as touch to focus! Let me know if you have any questions. Thanks - Ryan

u/RBMT_Media — 11 days ago

▲ 1 r/SonyFX6

FX6 won’t output RAW to Ninja TX Go

Sony FX6 (Firmware V6.00) + brand new Atomos Ninja TX Go.

I’m trying to record ProRes RAW over HDMI and have narrowed the issue down quite a bit.
What I’ve verified:

●	FX6 firmware V6.00  
●	Factory reset performed  
●	Ninja TX Go is brand new  
●	Same HDMI cable works with my A7S III  
●	Ninja correctly identifies the FX6 as “ILME-FX6V”  
●	FX6 enters “RAW (HDMI) + XAVC-I” mode  
●	Top of FX6 screen shows “RAW Stby”

Interesting behavior:
When the FX6 is in RAW (HDMI) + XAVC-I mode and I go to:
Monitoring → Output On/Off
Both SDI and HDMI are greyed out and show OFF. The camera displays “RAW Stby” at the top of the screen.

On the Ninja TX Go:
● Camera is identified as SONY ILME-FX6V
● Signal is detected
● Input shows “HDMI Standard”
● Red “NOT RAW” indicator remains active

Additional clue:
If I set Monitoring Output Format to QFHD (3840x2160), the Ninja often loses signal entirely and shows NO INPUT.

For comparison:
Using the exact same Ninja TX Go and exact same HDMI cable, my A7S III is recognized properly and does not show the NOT RAW warning.
Has anyone run into an FX6 entering RAW HDMI mode but the Ninja never recognizing the stream as RAW? Is there a specific FX6 RAW output setting I’m missing, or does this point toward an HDMI hardware/handshake issue?

I’m pretty dang frustrated this won’t work when I’ve seen it work on other folk’s FX6/Ninja

reddit.com

u/DamnitDogan — 11 days ago

▲ 2 r/SonyFX6

No audio over SDI (6G) at 4k

Hey all, just got a nice used Atomos Shogun Flame and tried to set it up to record today. I'm getting image, but no audio when outputting to 4K (3840x2160) over SDI. Audio does come through when changing the SDI output to 1920x1080 however. Is this possibly a cable issue (need a higher rated SDI cable perhaps?) or a settings/firmware update issue? Any help would be much appreciated!

Note: I'm running a mic directly into the FX6 and can confirm it's good on that end. That mic's audio does come through to the Shogun Flame on 1920x1080, but drops out as soon as I select 3840x2160 on the FX6 SDI output settings.

reddit.com

u/lassy-boi — 12 days ago