r/brucefw

Todas GPIos do ESp32 externas , Nrf24 , cc1101 interno , ir transistor, IR receptor , NFC interno , bad USB , e leitor de micro SD tudo nesse projeto ... E com Bruce firmware rodando em ESp32 s3 , fiz a PCB caseira na CNC , esses projetos estão me ajudando a desenvolver minhas habilidades em 3d e PCB , sempre fui apaixonado em eletrônica , eu sempre quis saber como as coisas funcionam.. resumindo é um projeto único , para entrar na coleção

Looking to add antennas and just flashed bruce

Also inspierd by the flipper zero

This version has: nrf24,cc1101,micro sdcard,ir led and ir receiver.

Фантомные нажатия

Inspired by the flipper zero

Usei uma bateria de iPhone 12 Mini e uma caixa impressa em 3D.
Adicionei 4 módulos:
Receptor IR
Transmissor IR
PN532
CC1101

Adicionei também um botão para desligar o aparelho.

Quem quiser o modelo 3D posso disponibilizar.

Hello, I’m new to this but I’m about 4 months into this tension headache from learning. I have a flipper zero I had previously and professionally i build motorcycles and fix /modify clusters and do odometer corrections so i can microsolder and use a multimeter and I have digital microscopes as well as a 55” Intouch pc running kali to check the rssi before and after.

My goals are to try and build the beefiest yet usable device I want the limitations to be only because it’s not a computer so basically best it can be.

I planned on running multiple nrf24 I have 4 available
Also hooked up to rabbit labs flux capacitor (c1101 boosted)
Running ebyte 900m30s 915mhz
Nm Cyd c5 resistive 2.8” for the new WiFi capability
I also planned on running a esp32s3 lonely binary
I ALSO have a cyd S3 2.8 capacitive touch at disposal
GPS is sequre m18-10 and I converted it to external antenna
I have 4000mah 3.7 lipo
5v hydraulic bearing brushless fan turbo shaped
I have a bunch of ipex to sma adapters
3 antennas for 915mhz
A small tx433-js-5 antenna that came with flux capacitor
Also have the voltage step up module
And a few battery charge modules

My questions:
The flux capacitor has a ipex plug on it what is that for? It already has an antenna mount. Could that be utilized to benefit its strength?

The s3 lonely binary has external ipex plug. Do I still need to mess with the o ohm resistor?

How many nrf24 are beneficial? (I guessed 2)

How in the world do I convert the c5 to external antenna there’s zero online for which traces to cut I have the the shield removed to see better

I keep having issues with Bruce not finding nrf24 when testing them

The gps, i have no interest in war driving. Is that practically all it’s good for in my setup?

Antennas which ones need to be separated, and can i have them all vertical and side by side?

Is it possible to run both Cyd and the esp lonely binary together. I was thinking about having screen 2 continuously stream the signal strength of each and the current gps location

Is there anything special for mounting the Lora module? It’s a big rectangle with solder pads below it.

Can anything be integrated? Like connecting all together as one unit. I do have perforated circuit boards of many Shapes I can use and I have a big box of circuit boards from kids toys, to flat screens, cable boxes, anything and everything common in a household so if I need anything I probably have it.

Also is there anything I’m overlooking or any info you think I should know

Thank you a ton! Here’s a photo of the traces on c5 and photo of Lora

The red dots on drawing are areas I took the surface off of gently to use multimeter and all points had continuity with ground so I’m assuming it’s layered.

If I have Bruce installed on my M5 StickCPlus 2 and open Settings, Why does it look like this and how can I fix it?

Had one of these boards laying around and wanted to see if I could get it working (large antenna for cool effect). Open to suggestions what else I can add!

So far everything works using a custom firmware config; wifi/ble, uc6580 gps and sx1262 lora. I also use a ST7789 2" tft and an spi microsd. I think these boards were meant for meshcore but it's cool to see them work on bruce better than even I expected.

The 3d printed case I made for it is a bit bulky, but I did want space to add more stuff later.

0sens3 on Instagram

https://www.instagram.com/0sens3?igsh=NTc4MTIwNjQ2YQ%3D%3D&utm\_source=qr

Check out my case available on MakerWorld!
Link is in my Instagram bio
A like and follow on Instagram would be great so I can continue to make dope stuff with my time

This case features use of M3 riv inserts
4 antennas placements
Thick rear for support
GPS slot for led exposure and antenna fixture

Not as much as an innovator but I’m definitely familiar around hardware
I’d love to create something like this in the near future but so far I have come to reproducing great projects with a little bit of my influence contributed

Check out the build! And hopefully this case will be modular enough to fit an esp32 dev board utilizing a ST7789 display or the ILI9

So finally it works, this case is for the CYD and the NM-RF-Hat with turnknob to switch the modules and the display in landscape mode.

So i put everything on Thingiverse, https://www.thingiverse.com/thing:7373901 where you can download the files and a simple manual like always, use at your own risk and don't forget: https://buymeacoffee.com/monduesea

I do that as a hobby but I also have to buy some stuff for those projects, thanks.

🚀 A premium OTA firmware launcher and application manager for ESP32 Cheap Yellow Display (CYD). Browse, download, rate, and boot apps over-the-air or via SD card!

QuadEver Launcher is a highly optimized, feature-rich resident firmware launcher and app manager designed for the Cheap Yellow Display (CYD) ESP32-2432S028R development board. It allows users to store, browse, flash, and boot multiple application binaries (.bin files) from an SD card or wirelessly via a Web User Interface, transforming your CYD display into a versatile multi-tool.

GitHub:- https://github.com/samiralam5755/QuadEver-Launcher