r/polymer80

I have this piece stuck on two different 43 slides. One is a psa dagger slide and the other is a p80builder slide. I cannot figure out how to get it to move to remove the extractor. Help please

Is this all I need to complete my geisler g19 build ? Or am I missing something ?

Geisler frame with Hooper Gun Works g26 slide and Herrington Arms HC95 V2 (waiting on holosun warranty for my red dot)

Has anyone successfully fit the Grip Force backstraps on a Combat Armory CA19?

Iove this frame but hate the slide slicing my hand... I've asked Rapid Engineering to make one for this frame, but they need much more demand to make it happen.

first time doing anything like this, i know it aint the prettiest and isnt going to be perfect but i would like some feedback on how it is looking.

the "4mm" hole is not overdrilled, i just ran too far through on each side(polymer is a lot softer than i thought lol). it did not poke through the other side, more so just widen the inside of the hole.

i also am aware i do not have the blocks glued on yet, i am waiting on my glue, thank you guys.

For my first and probably my last PF45 should I go with a 20 Longslide or just a 20 slide my original goal was to have every P80 Size which i did. Next goal is to have every Glock Size I have them all except for competition and long slide. I was originally going to get two more full-size V2 frames to do a 17L and a 34 competition. I had my eyes set on a slide I liked for my 20 as they’re scarce and an idea but I just stumbled on a 20L Slide that I like as I couldn’t find one I liked for awhile(It’s alright I wish I could find a better looking one) it’d be cheaper to knock out the long slide with this PF45 and put a 20L on it, but I’d get more guns if I got two more full-size 76%or80% frames and did those Comp&Long and made the PF45 a Normal 20 what should I Do ?

Is this enough to complete the lower or am I missing something

My second 76 frame. Don’t mind the 2nd hole, I was being stupid😭 my jig on the way so I can do the holes correctly. 4th hole done by me no jig, fit pin with rails good. Been working on this for 2 hours, Just need to work on the rest of trigger housing🫩

SCT Manufacturing 43SC
Streamlight TLR-7 Sub ⚡
Miami Night 2-Tone IWB from IKC 🌴🌆

Finished with DCC foldover clips + mod wing for a locked-in concealed carry setup.

This combo just screams retro synthwave vibes.

#SCT43SC #SCTManufacturing #TLR7Sub #MiamiNight #Kydex #EDC #ConcealedCarry #IKCHolsters

Drill a hole in the magwall, but I’m not too worried about that😅 drilled the 4th hole no jig by myself, now I’m just waiting for my jig and lpk to ship.

Jigs and tooling are officially back in stock.

We just want to say thank you. Truly.

To everyone who stuck with us, supported us, checked in, placed orders, sent messages, and kept standing behind 80% Arms, we appreciate you more than you know. It has been a long road, and your patience and loyalty have meant everything to us.

Easy Jigs, end mills, and tooling are live on the site again. And if you haven’t checked it out yet, take a look at the new Easy Jig® Gen 4, our most advanced multi-platform jig yet.

Thank you for being part of this fight with us.

Now let’s get back to the bench.

I can’t seem to get myself to throw out the plastic ones even though I know I don’t need them anymore, excluding the p80 one. I can’t be the only one, right?

Is there any demand for a PF9SS these days? I bought this just before P80 shutdown making the 80%’s. I’m not active in this subreddit and don’t know what the value of this stuff is.

Hello I hve a question about my gen 3 26 the magazine only comes out when heat I applied but once the heat is not present the magazine doesn’t want to slide out or even come out without me forcing it the hell out of it I tried cleaning the inside used gun cleaned and lube and still didn’t help this happened before but I just used cleaned the inside where the magazine goes and it went back to normal but now it won’t work please can use some help

P80 Full Size Frame
Zaffiri Glock 17L slide, lightning cuts
Zaffiri ported barrel
NDZ recoil rod, 20lb ISMI spring
OEM internals
Holosun 407C
Magpul 17rd mags
124gr S&B ammo

This build has approximately 800 rounds through it and has consistently had an issue with the slide not fully going into battery after a few boxes of ammo.

This presents two ways:
The slide stops with about 1/4in to go
The slide stops with the round half way into the chamber

In both cases pressing on the rear of the slide with my thumb is enough to get it to finish going forward. Prior to switching to the 20lb spring I could get the first scenario to sometimes happen just by slowly moving the slide forward and letting it get “stuck.”

The first 600 rounds were with an OEM recoil rod/spring. I switched to the 20lb spring and slip2000 for lubricating the slide for today’s range trip.

It was perfectly clean before the range trip. I think the slip2000 got slung around and captured a bunch of carbon. Put 200 rounds through it today. The slide issues happened 4 times (which is an improvement).

I don’t see any excess carbon build up in the chamber and the feed ramp wipes clean and is very smooth. No signs of obvious wear marks on the slide or frame.

Does anyone have any ideas for what I should check next on this build? I’m going to get it cleaned up this evening and take another look at things.