My T1 build has been running fine on stock, it is flipped and fully aircooled with two 120mm fans as exhaust. No complaints so far and was just wondering, what do you guys think are the most essential mods someone must do to enhance the performance of your PC?
Hello,
I’m looking for an AIO compatible with the FormD T1 2.1.
For my ryzen 7 9800x3d
I’m using an ASUS Prime RX 9070 XT, which is 50 mm wide, so I have to set the T1 to the 2.75-slot configuration.
I’m therefore looking for an AIO with the following requirements:
240 mm radiator
Radiator thickness of 27 mm maximum
Pump block height of less than 55 mm
Tubing that is flexible enough to route around my RAM, either above or below it (G.Skill Trident Z5 Neo DDR5-6000 CL30)
My main requirement is that I absolutely want an LCD display and RGB fans. The NZXT Kraken Plus RGB seems to meet all my requirements, but I’ve heard that its tubing is extremely stiff.
I don’t necessarily need the tubing to run underneath the RAM; I mainly want to be able to route it around the RAM, either above or below it.
Do you have any other models you would recommend that could meet these requirements, particularly ones with tubing that is flexible enough for this type of compact build?
Thanks in advance for your suggestions!
Wind valley kit installation case
Planning to build. 9800x3d on a formd t1.
Gpu is power color reaper 9070xt but i have it configured to 2.25 slot
What would be my best air cooler option under 67mm?
Please help me decide between axp67,53,47 or is 55,67 thank you!
Mostly finished with this. Waiting on a top fan shroud and taller feet for the bottom. Open to feedback or anything else I should do :)
• Case: FormD T1 v2.1, black, sandwich layout
• CPU: Ryzen 7 7700X, -30 Curve Optimizer
• Cooler: Thermalright AXP90-X53 Full Copper, stock fan swapped for an ID-Cooling TF-9215-K
• GPU: MSI RTX 5080 Shadow 3X OC
• Board: Gigabyte B650I AORUS Ultra
• RAM: 32GB G.Skill DDR5-6000
• PSU: Corsair SF850 (ATX 3.1), right-angle 12VHPWR connector on the GPU
• Fans: 2x Arctic P12 Pro PST on top as exhaust
Worth noting I didn’t optimize any of this for noise. I game in noise-cancelling headphones, so fan noise doesn’t bother me at the moment.
Edit: bullet formatting
I recently bought the Ncase Formd T1 Gunmetal and I've been loving it. However, one thing that struck me when it arrived was that the color was a little bit darker than I assumed. Recently I have been looking at pictures of other's Gunmetal and I've checked the website and it seems that they have indeed sent me the wrong color. Do you guys see it like me or I'm just paranoid? Also, I checked the warranty policy and it seems that I am not eligible to claim the warranty as they say "These are inherent to the manufacturing process and do not constitute a defect in materials or workmanship". Is there really nothing I can do?
Any help is appreciated!
Hello all,
I’ve been wanting to make a switch to my GPU. It’s been a while since I built my T1 PC…I currently have a 4080 FE, but I’m starting to regret the blower fans and wanted to switch to a three fan GPU. Are there any real benefits changing or am I just delusional?
Hello I am planning a build around the T1 (after receiving the m3 I wanan go even smaller)
9800x3d + 5090 FE 1000W psu
As we all know nvidia screwed up with the 12V high power connector and a solution is the WireView pro which monitors the pins in the gpu
For the FE since it’s slanted you’ll need to get the wired version
The way it works is that theres a cable on the wireview that goes into ur GPU and u plug in your own cable into the module (custom cables will be made for this) but the problem is mounting the module somewhere/clearance for it
If anone has some this let me know, I don’t really care about displaying the module as I can just have it show up on one of my monitors but if you have send a photo please