u/Danishor

I am on IOS 26. I went back into my photos to find my lockscreen photo of my daughter and discovered I deleted it a while ago. How can I get it recovered?

Few things I’ve tried and found online:

1. “Show in photos” when customizing the lockscreen. This option is not available or showing for me.
2. Checked every possible place I could have sent it, no avail.
3. It is not in my recently deleted.

Any help would be appreciated, even as far as accessing the iPhones file system if needed.

Howdy everyone,

I am looking to register an NFDD (flash bang) in Texas as a private individual and had a few legal questions I am hoping a few of you might be familiar with.

Few prerequisites I think will be addressed in the comments:
- I found a company that will assist me to Form 1 a flashbang.
- The company will provide fuses so long as I have a registered hull.
- Destructive devices are allowed in Texas.
- I am a private individual, no FEL
- I am aware of magazine storage requirements. For now consider it same day mix and use for the device so storage and transportation are non-issues.

Here is my question: am I legally allowed to fill the flash bang for use on private property in Texas or is it essentially a paperweight with an interesting story?

My concern is the energetic material the Flash Bang is filled with. Federally it isn’t an issue so long as the device is registered, however my concern is state law.

Any experience, knowledge, or legal reference to on this would be appreciated!

I’m finding conflicting information on this topic and cannot get a clear answer. Is hobby/private use energetics good to go in the state of Texas?

If you have a reference or source to go with what you know that would be appreciated.

Thank you

Located in Texas. Found 50-60 in my bath tub by the window. Couldn’t figure out where they were coming from. Concerned it is termite warmers.

About 1/4” in size head to butt, maybe 1/3”

Howdy everybody, running into a bit of issues with my micro, and I’ve ran out of ideas. Hopefully someone can point me in the right direction or help me out.

I have a closed bolt FA Micro Uzi (Registered Bolt). I’ve put about 3500 rounds through it with no issues. I can probably count on one hand how many malfunctions I’ve had during that time. Stripped to the bare receiver to clean. The next day I begin having significant issues.

The issues are not wholly consistent. One day I am having one issue the next I’m having other issues.

First 2500 was S&B 115gr
Last 1000 was Monarch 115gr (couldn’t get ahold of S&B for a bit)
Currently running the Monarch

NOTE: I know Monarch isn’t the best ammo, however it ran the last 1000 without any issues.

NOTE: I run the bolt without a trip. Never had issues without it, neither has my father in the 30-40 years he’s ran them

Here are some changes I’ve tried:

1. New FA extractor
2. New Semi extractor (cause why not try)
3. Stretching the mag spring
4. Ejector is firmly riveted, not moving, and centered.
5. Bolt freely slides in the receiver, not binding
6. different barrels
7. Ensured feed ramp is free of carbon
8. Inspected the bolt for burrs, none found.

I ran 250 rounds today with an IMI mag and a new FA extractor. Kept detailed notes, here’s what I got:

Tested FA extractor, Semi extractor, stretching spring, 2 barrels, supressed to give more back pressure at separate times.

2 mags ran with no issues

10 Failure to eject (stovepipe)
3 failure to feed
1 failure to fire
7 failures to extract (all while supressed on 1 mag)

NOTE: I have noticed 1 correlation in the data I’ve collected: ALL malfunctions in the 250 I ran today were mostly in the first 1/4 mag, all within the first 1/2 mag.

Any help would be greatly appreciated. Should have a 1 day turnaround with testing ideas