Hello guys I tried fitting the washer after the FMIC but won’t fit anyhow, I’d have to deform the plastic but now I’m too far gone and it’s unrecoverable.
Did u buy any after market washer bottle? If u have can send picture and article? Thank u
I have 15” wheels and I wanna go for 17”, but I’m very ignorant on the matter and I have no clue which fits and rides better.
The only thing I’m sure is that for now I don’t wanna roll fenders so I’d like something that fit as is, or if it needs slight camber it’s ok.
I’ve been told 17x9 with ET from 15 to 25 is a great fit without needed modifications, with tyres 235/40
sorry this will be the last post about it ahaha
Im so happy about everything I’ve done except welding, that thing will never look good even after paint
The only thing I’m not happy is the terrible job I did welding, was the first time for me. I still have to sand it down prime and connect all the power in the bay to test
Hello guys, I need to remake the positive terminal but I have a doubt:
When I see people making new battery terminal I see cutting all cables and joining together in a single ring terminal or multiple it doesn’t matter, then bolting directly to the power, but I also heard people saying this is a fusible link, so crimping them all together wouldn’t be the safest and most correct approach.
What exactly is this, does it have fuses in, what is the proper way of rewiring this component? It’s 3 cables, 1 thick and 2 thins
Hello guys I’ve finally removed the tray and now I wanted to buy the elements needed for relocation.
I have stockish ca18det, no audio system, stock starter etc.
What is suggested for the power wire? 35 or 50? And for those who know, how many meters from the trunk to the engine bay?
My list for now is:
- a battery tray for the trunk
- 5m 50mm power wire (Im not sure about these specs)
- 1m 50mm ground wire
- 1 fuse holder with 150A fuse
- a 50mm 1 input power distribution block with 2 to 4 outputs for starter fuses etc (are they always insulated? Are there specific products for this goal?)
And the various terminals depending on what I buy in the list. If u have any suggestion or specification since it’s the first time for me.
I checked some kits but they always seems to miss something, if u can link me anyone you used that works for this goal I’ll happily buy it instead of purchasing individual items.
Thank u in advance <3
As u suggested I also followed a couple of template pictures and I think I got all the spot welds, drilled bigger holes but It still won’t move an inch. Any suggestion?
Im doing a battery relocation to clean rust and to route the new intercooler and I’m swearing hard on this battery tray.
On god my eyes aren’t trained I can’t see those spot welds, I think I drilled a couple but I’m not even sure at this point. Battery tray isn’t moving a single bit, also I fear it has a couple of spot welds on the sides which are unreachable since I have the engine in.
Do u see anything or direct me anywhere? Thank u
Hello guys I wanted to purchase seats and I would really love to get some s15 but there is nothing in my area, they are very expensive over seas with customs and shipping so I ended up deciding for the ones in the picture.
Of course they won’t fit into the OEM brackets so I was wondering what would be the right article to buy, will any of these work for a proper installation?
https://www.driftshop.com/superlow-bucket-seat-mounts-nissan-s13.html
https://www.driftshop.com/bucket-seat-mounts-nissan-200sx-s13.html
Thank you
Specifically on the CA18DET.
I found a seat Leon cupra (280cv) IC in my shop and I was planning to mount it but by watching at the bay I kinda feared like i would need to relocate the battery somehow
I’ve been hating on the OEM seats on the s13, I just move around everywhere on any corner.
I don’t wanna go any racing or rigid thing but I have no experience in seats, I’d love to keep 90 design just a firmer one. Do u guys have any preferences? Link or pictures would be amazing
I wish I could have wired on a OEM button but my knowledge in electronics is very basic, couldn’t make it work, so I added an external switch
I’m almost done with gauges and now I have this problem to install the oil pressure sensor on the car. Since I don’t wanna remove and replace the original sensor that goes to the ECU, how could I install an additional one? Oil press gauge is defi
I just installed the multi gauges and run all the sensors through the firewall, kit came with a T connector for a 5mm tube. Where is the right location I should cut and connect it? In the intake manifold? If anybody has a picture or something it would help a lot