What’s your guys opinion on this truck I’m looking too purchase? Is it worth it? And I’m a little sceptical on why it’s so cheap with the market for these trucks being pretty high around me.
I am thinking about selling my project truck but I’m not sure if I should sell it all with the parts I have for it or should I part it out
It’s a 2003 dodge 2500 SLT quad cab long bed 4x4 5.9 cr it’s got a 48re in it instead of the 47re. Which is not done being installed. I have receipts for everything I’ve bought for this truck I have between 3-4k in parts and I bought the truck for $1,750 and I bit off more than I could chew. With being busy with my full time job and the army on some weekends I don’t have a lot of time too work on it anymore so I found another Cummins that I want and I am willing too make payments for but I want too get the most I can out of this truck. It’s not the best looking truck out there at all and I know the truck doesn’t cost a lot but it’s the parts and time I’ve put into it. I live about 1hr 30mins south of Michigan city and I’ve drove too Ohio 3 times for parts which is around a 3 1/2 hour drive one way. I have put upgraded parts on the truck and have upgraded parts for it. Like banks monster ram and boost tube, Fass 165, xdp competition and towing flywheel, and all new upgraded CAT filters. It’s got a gooseneck hitch in it and is lifted a little bit. I’m just not sure what too do too get the most money out of it.
I have a 2003 dodge 2500 4x4 5.9 cr. I just started the swap from the 47re too the 48re and everything was good until I figured out that my truck has wiring for the 5 pin nss and the transmission has the 3 pin nss. I’ve heard use the wiring that is on the truck so I was wondering if I could change the sensor out on the transmission from the 3 pin to the 5 pin nss.
Thank you for any help in advance.
This might be a lot too ask for so bear with me here.
I’m currently 18 163ibs 5’8 male
I am tired of saying next week I’ll start doing better I want too make a change. I am in the army guard and I’m tired of being a shlt bag in my eyes. I graduated basic training in July 2025 and I got back to ait in August because of split ops training because of high school. I started a full time job in a factory when I graduated mid terms in December. I work night shift from 4pm too 2am 4 days a week (mon-thur) and I usually work 6 hours of overtime on Friday (most of the time unless I have drill on the weekend). I don’t really have a weight goal or a lift goal yet because I don’t even know my ability’s. I used to lift regularly in school because of football and at a buddy’s house. But after basic training till now I’ve not even lifted a handful of times and I occasionally run. I eat like crap usually a small meal of leftovers from what my parents made the night prior. Most the of the time I eat a snack like a bag of chips or a gas station pizza between when I get too work and 9pm when I go too lunch. I eat 80% of the time a home cooked meal at my gfs house for lunch. Then rarely have a snack which is another bag of chips before I get off of work. I go home and eat whatever my parents made for dinner. I have a bad habit of heating or making too much food for myself and eating it until I’m overly full because I don’t like to waste food (which ik is my fault).
My goal is too work out at least 3-4 times a week and make myself pre made healthy meals too eat and get rid of the snacks. The weekends are hard for me because I’m not home usually. I want too loose wait and gain muscle too excel in my military career. What is everyone’s advice for meal preps and lifts. I also want too hit hard on cardio too be better at running I’ve never been a runner other than sprinting for short distances. Lifting wise I need help on what lifts I should hit. I’m looking for full body lifting no just bench and squat.
Thank you for any advice and help with this I’ve been kinda lost on where to start and I’m tired of making excuses I hope this all makes sense and I didn’t add too much non needed info.
I just got my 17 PM and have been looking for cases. I work in a factory on concrete floors and need a good case. I was looking at the otter box but I don’t really want too spend 70$ for it unless it came down too it. So what is a good case that’s not super flashy and or bulky and is mag safe.
Thank you for any suggestions.