u/Good_Upstairs1867 — reddlx

Trying to mod an oled switch. But getting a purple screen.

For diode values

C point 0.649

A point 0.456

D point 0.619

B is 0.893

The chip glitches the switch to picofly page no sd. Its only when i try to bypass using power + vol -/+ it will go to purple screen when trying to load ofw.

I checked online about point a if its dislodge or broken. Thats when I do forward bais i get 0.456 and when I try to see if one side is short only one side goes to the ground other side does not short to ground. I tried to ohm it and the value is about 1.098 M ohms. When i Googled this type of troubleshooting it says 4.7kohms but I did not remove for accurate measurement...

Im looking for suggestions... coz other oled I've modded didn't end up like this. I do not think the emmc is the issue coz when I remove the modchip it loads to ofw.

reddit.com

u/Good_Upstairs1867 — 15 hours ago

▲ 1 r/SwitchPirates

Back up and restore now it won't boot atmosphere

So I was transferring my sd card to another modded switch. I thought it would be a simple backup and th3n restore to the new modded switch. I followed some instructions from Google. I thought it was successful in restore the the files I backup but when I try to load the cfw it just goes blank screen. I am trying to skip loading the games and my saved games..

I have 2.74 latest picofly firmware. The old switch had 2.73 im not sure if that affects anything.

Should I restore load delete atmosphere 1.11?

Switch oled firmware is 22.2

reddit.com

u/Good_Upstairs1867 — 1 month ago

▲ 2 r/NxSwitchModding+1 crossposts

Using a already setup microsd to another modded switch.

I purchased a oled switch with totk theme. I have a modded switch already with 1tb has android Linux and hos installed. I want to be able to just use the existing sd card to the newly purchased oled switch without having to restart any of the setup? Is this possible?

reddit.com

u/Good_Upstairs1867 — 1 month ago

▲ 2 r/software

IMG BURN ERROR

I 18:49:49 ImgBurn Version 2.5.8.0 started!

I 18:49:49 Microsoft Windows 8 Professional x64 Edition (6.2, Build 9200)

I 18:49:49 Total Physical Memory: 16,709,488 KiB - Available: 13,203,032 KiB

I 18:49:49 Initialising SPTI...

I 18:49:49 Searching for SCSI / ATAPI devices...

I 18:49:49 -> Drive 1 - Info: XD External bluray C402 (I:) (USB 2.0)

I 18:49:49 Found 1 BD-RE!

I 18:50:02 Operation Started!

I 18:50:02 Source File: F:\nintendo switch\henloader-AIO.iso

I 18:50:02 Source File Sectors: 153,600 (MODE1/2048)

I 18:50:02 Source File Size: 314,572,800 bytes

I 18:50:02 Source File Volume Identifier: HenLoader_AIO

I 18:50:02 Source File Volume Set Identifier: 69263585296bb351

I 18:50:02 Source File Application Identifier: NetBSD UDF

I 18:50:02 Source File Implementation Identifier: NetBSD makefs 10.0

I 18:50:02 Source File File System(s): UDF (2.50)

I 18:50:02 Destination Device: [0:0:0] XD External bluray C402 (I:) (USB)

I 18:50:02 Destination Media Type: BD-R (Disc ID: VERBAT-IMe-000)

I 18:50:02 Destination Media Supported Write Speeds: 2x, 4x, 6x

I 18:50:02 Destination Media Sectors: 12,219,392

I 18:50:02 Write Mode: BD

I 18:50:02 Write Type: DAO

I 18:50:02 Write Speed: 1x

I 18:50:02 Hardware Defect Management Active: No

I 18:50:02 BD-R Verify Not Required: Yes

I 18:50:02 Link Size: Auto

I 18:50:02 Lock Volume: Yes

I 18:50:02 Test Mode: No

I 18:50:02 OPC: No

I 18:50:02 BURN-Proof: Enabled

W 18:50:03 Write Speed Miscompare! - Wanted: 4,496 KB/s (1x), Got: 8,991 KB/s (2x)

W 18:50:03 The drive only supports writing these discs at 2x, 4x, 6x.

I 18:50:19 Filling Buffer... (80 MiB)

I 18:50:19 Writing LeadIn...

W 18:50:19 Failed to Write Sectors 0 - 31 - Reason: Write Protected

W 18:50:19 Retrying (1 of 20)...

W 18:50:19 Retry Failed - Reason: Write Protected

W 18:50:19 Retrying (2 of 20)...

W 18:50:19 Retry Failed - Reason: Write Protected

W 18:50:20 Retrying (3 of 20)...