u/Ian-99

Hey all, I am hosting a bachelor party for a freinds and all of us are firearm owners and wnated to have a range day for this gathering as we all rarely are in the same spot at once. I see Keystone gun range is clsoed due to Stage 2 Fire concerns. This range would have been ideal but I dont think itll be open before the end of the month. The next closest is Gypsum gun club which is kind of public? seems they have very strict times on events and im not sure if they will be open to us showing up. trying to communicate with them on that. outside of that I dont see anyhting else in the area?

Maybe im missing an option? I typically visit Great gunns out in nunn but thats about half way accross the state from where will be staying so that doesnt work great. any suggetions?

Thanks!

Helloe, Im new to the standing desk thing. However I work from home and its becoming apparent I am not moving enough during the day.

My biggest issue is finding legs that will fit my desk. I am a welder adn can fabricate really anything. My desk is abou 9 feet long and 32inches in depth. I am struggling to find legs that will accomadate my large desk. I would ideally be ok with a set of 4 legs even if I need to make custom brackets to mount them to the desk that is fine.

Everything I have found is either a frame or a 2 post setup that is obscenely expensive. what are my options?

Desk is 9ft X 32". Frame and top is steel so its about 170LBS.

Hello everyone. As most owners are aware, the Gauge Cluster Lenses in Mazda CX30/50 is made of playdough and dead dreams. It scratches just by looking at it. leaving some less desirable glares especially when in direct sunlight.

However, the Lens is not too hard to replace. you need 3 total tools.

Tools: T15 Torx bit with some way to turn it. (I used a 1/4" socket extension on mine, no need for a ratchet though).

some sort of small pick and small flat head screwdriver.

NOTES: My new lense did not arrive perfectly from Mazda. it had some scratches. I was able to clear it up using Meguiars PlastX compound and a very soft/clean Microfiber towel. An air compressor is a great tool to remove dust right before install. Towels will always leave a little fuzz behind and once the lens is on, anything on the back side is permanent. Clean the lens carefully before install and be sure it looks as best as you can make it. It's a shame Mazda chose such poor material for the lens. But the care is great otherwise.

I would have posted more images of removal of the lens itself but Reddit will not let me add more images. Advice is to just take your time with the lens. it should not require much pulling force to remove once all clips are free. Also, gloves are recommended here, finger prints will ruin your day.

https://preview.redd.it/evdwwjhm38yg1.jpg?width=3000&format=pjpg&auto=webp&s=368732d086ee159d3e0b10af4e901a9dad528cd3

Step 1 is removing the driver side vent. This just clips in and can be pulled out by hand. I recommend getting fingers underneath and to the side of it.

https://preview.redd.it/c7z6gdk948yg1.jpg?width=3000&format=pjpg&auto=webp&s=1e5f0aba994a2ed50d7e1e18b2e6a93463376cbd

https://preview.redd.it/in452hk948yg1.jpg?width=3000&format=pjpg&auto=webp&s=ca345096d46d704f7c9700c35f37e00ce10ea7db

Step 2 is the passenger side Vents/ Facade. This is easiest to access with the passenger door open and is also just clipped in and comes out pretty easy.

https://preview.redd.it/64xmkbhe48yg1.jpg?width=4000&format=pjpg&auto=webp&s=6ecb38bb4a5f3960298a5528ad261942107df636

Step 3 is removing the trim around the gauge cluster itself. Both driver side and passenger side lower dash trim pieces can be partially removed to make some room.

https://preview.redd.it/vfz8iy4h48yg1.jpg?width=3000&format=pjpg&auto=webp&s=3638072dacc425264c81fc85ff910621ea7a0e16

https://preview.redd.it/8gyy4y4h48yg1.jpg?width=3000&format=pjpg&auto=webp&s=aafbd1e59b3c68442556a5b539b9073056f01e34

https://preview.redd.it/vkzoly4h48yg1.jpg?width=3000&format=pjpg&auto=webp&s=4160673508d90a2c8ec1340a811e05dba999d4be

Step 4 is removing the wired connection behind for the trim buttons around the lens itself. one on both sides.

These are just push clip connections, I found a small pick to help push the clip down helped a lot as they are very small and difficult to get fingers on.

https://preview.redd.it/37ss4tfj48yg1.jpg?width=4000&format=pjpg&auto=webp&s=ff2d540f02ab7669461fbc28b0f379574a686205

https://preview.redd.it/rtgc3xej48yg1.jpg?width=4000&format=pjpg&auto=webp&s=c85def5ee16ca78926a734c59b78fe69e474c53d

https://preview.redd.it/74xu7yej48yg1.jpg?width=4000&format=pjpg&auto=webp&s=fb3994678dc3d4789f5fb29d2b5d8909b0b3cec5

https://preview.redd.it/hxtbcxej48yg1.jpg?width=3000&format=pjpg&auto=webp&s=1c3e91b1df51857e4efde8b4d78f1f1b4f710ff4

Step 5 is removing the gauge cluster trim itself. you must remove the 2 Torx screws located on the top right and left of the trim piece. Be careful these screws are short and easy to lose inside of a vehicle. T15 Torx here.

https://preview.redd.it/3g0hqmzm48yg1.jpg?width=3000&format=pjpg&auto=webp&s=f05210ec2b3c5292c3accb1e1bd8fc80cec4083c

https://preview.redd.it/jljehmzm48yg1.jpg?width=4000&format=pjpg&auto=webp&s=007836f82373f62c6855704e9054beb3e1a18c10

Step 5.1. The trim piece between the steering wheel column and the clips into the gauge lens trim. Carefully remove the clips, as noted in the image it has 3 clips total. 2 left and right. 1 in the center.

https://preview.redd.it/6n6k1myo48yg1.jpg?width=4000&format=pjpg&auto=webp&s=0047c4c37b03d7dea16cba63350297d5ec4ecdd5

https://preview.redd.it/4j1g6myo48yg1.jpg?width=4000&format=pjpg&auto=webp&s=ef10a15c85d34e274c4211c84f44b137b8c5b29c

Step 6 is removing the Lens itself now that the lens trim is removed. BE CAREFUL. The plastic this is made of is very brittle, scratches easy and cracks easy. This lens has 9 total plastic clips that must be pressed down by a pick or other tool. do not try to rip the lense out, you will break it like I did. You'll notice on the bottom it has 2 prongs, these prongs I believe are to only be used for installation. underneath the lens adjacent to the prongs you will see 2 clips, these 2 can be pushed up with your fingers and you should feel them pop. Along the sides you will find clips that need to be pushed inward as well. These will likely also pop. The top 3 clips are tricky because you cannot get fingers on them. I suggest using a small angled pick to get into the hole and press down. These should also pop when free. The lens should require very little pulling effort to come free.

On reinstalling I highly suggest before clipping the new lense in, set it where it will live and inspect it. This is the last opportunity you will have to dust / clean the back side of it. BE SURE IT LOOKS AS YOU WANT before finalizing the install. Be sure the wires are clear on the lens as well, they can get pinched. once you can clipped it into the dash. verify its seated all the way, the gauge lense trim will not go back on it and the lens itself is not seated. Nothing during this install requires much force at all. If you are forcing anything you are doing it wrong.

Once the trim is installed, wires are plugged back in. The lower trim around the steering column will need to be lifted up a bit to re align the clips. Once that is back in place the Driver vent and passenger facade piece can be snapped back into place.

Once assembled, you should have a cleaner lense. careful cleaning. Maybe try one of those Films, I have had terrible luck applying these to this lense though.

https://preview.redd.it/sblrgjks48yg1.jpg?width=3000&format=pjpg&auto=webp&s=ffb55d1de5fbf6ac5bec38f7fee549a408f56787

https://preview.redd.it/t79k6jks48yg1.jpg?width=4000&format=pjpg&auto=webp&s=9a44214ee025559adc30726acf9a205f3423d325