u/Icy-Seaweed-1044

Image 1 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 2 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 3 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 4 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 5 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 6 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 7 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 8 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 9 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 10 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 11 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 12 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 13 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 14 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 15 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7
Image 16 — Need helpSelling my 2003 AC Toyota Tundra v8 4.7

Need helpSelling my 2003 AC Toyota Tundra v8 4.7

2003 Toyota Tundra

184616 miles

With in the past 3 years

At 165593 water pump, upper and lower radiator hoses replaced

Radiator replaced

Thermostat replaced

Timing belt replaced

New tensioners

Belts replaced

Things listed above where done at Penske Toyota dealership Downey

Valve cover gaskets replaced

Evaporator check valve replaced

It has a k&n intake yes I do have the OEM one yes it will be included how else would you pass smog check in cali

New calipers both front replaced

New rear drums and shoes

Steel break lines front and rear

New steering rack bushings polyurethane

New sway bar bushings

Suspension Maxx sway bar end links

It currently has a rough country steering knuckle lift currently at 4inch height able to raise it to 6 inches

New 333 fabrication passenger side aluminum billet bracket for sway bar bushing

Gibson duel cat back extreme exhaust

JBA short headers

New lower control arms

New upper ball joint SPC control arms I’ve had them just recently replaced the ball joint

The rear has a helper spring and a 4 inch block

Tires are LT 315/70r17 Falken wild peak AT3 load range E still in great shape sitting on Mickey Thompson Side Bitters2

The exterior needs work bed damage fender damage needs paint on hood roof due to sun damage also has a few scratches. Bumper was replaced with a steel one from a 2002 had a lil kiss with a pole with the old bumper.

Frame is rust free been in cali all it’s life

Just installed TEQCUSTOMS headlights with projector style headlamps

It does have a pair of cali raised square fog lights on the front bumper

Just installed a new tonneau cover plastic I also have lights in the truck bed running along the sides

I did build a custom track with board to be able to slide in and out of the bed heaviest thing I’ve had on there would be around 600lbs of cement blocks it’s perty sturdy

It does have the tow package from factory

It does have aluminum running boards

The interior is in good condition

I have a first gen tundra modular astray phone holder with magnetic charger installed

A JBL head unit with kicker component speakers replaced oem they are paired to a 400 watt kicker amplifier 4 channel

Also a 800w kicker comp v enclosed subwoofer paired to a kicker mono block 1000 watt amp

Husky floor liners both front and rear

Led interior lights swap lil finicky but they work

Also dash lights replaced with LEDs

It has a viper alarm with remote start

The window hinges that break where replaced with aluminum billet ones

Rear windows are tinted 15% I believe

Dash has no cracks

Im including the cover craft uv series Sun shade

The garmen dash cam as well

Things that it needs is body work

A new power steering line it’s leaking the rubber one not the runner to steel one

Wheel bearings both sides

Lower ball joints running the big tires don’t help

Needs a new output shaft seal it is leaking a bit

Needs a center support bearing

Tags are good till next may of 2027

Lil back story the truck has been in my family since 2004 my parents owned it then gave it to me its been good to me and my needs but just needed more space for my growing family. As far as the salvage title we had a drunk guy side swipe my wife supposedly 4 other ppl hit him that night but any who insurance refused to pay the shop to do the work so they wrote it off and I bought it back from them.

u/Icy-Seaweed-1044 — 3 days ago

Headers

Waited a month for the headers to show up well worth the wait. Just a major pain to install but took my time and man no regerts. The truck feels awesome at take off. Haven't gone on a trip yet but can't wait. I also did suspension Maxx sway bar end links. Next project wheel bearings and polyurethane rack and pinion bushings.

u/Icy-Seaweed-1044 — 1 month ago

Headers

After a month of waiting i finally got them and installed them. Took two days but they are in there. Also installed the suspension Maxx sway bar end links. Next project wheel bearings and rack and pinion bushings.

u/Icy-Seaweed-1044 — 1 month ago