u/admkukuh

Hello everyone, i currently have a TP-Link EX511, bought used for cheap, working wonderfully on both IPv4 and IPv6 with PPPoE mode.

So the topology is like this:

ISP Gpon Router (PPPoE) -> Gpon Router Bridge mode to LAN Port 1 -> WAN Port EX511 -> EX511 PPPoE Mode (Router Mode) -> EX511 Lan Port -> EC230-G1 Lan Port -> EC230-G1 AP Mode.

On WAN settings for PPPoE, the IPv6 Address i set to auto to make it the same as the ISP Gpon Router, enabled both NAT and Full Cone NAT, and i entered a custom DNS 1 and 2 for both IPv4 and IPv6.

On LAN settings, I enabled the DNS 1 and 2 for IPv4, but on IPv6, i set it to RADVD mode + RDNSS enabled (ULA not enabled because idk what is this), With Delegation Type Prefered (not static) and the WAN for IPv6 is set at the WAN i created.

The question is, how do i set LAN (not WAN) Static DNS for IPv6 LAN just like IPv4 LAN that i can enter gateway and set static DNS? The other mode for IPv6 LAN is DHCP mode, idk if it will helps..

Hello everyone, i currently have a TP-Link EX511, bought used for cheap, working wonderfully on both IPv4 and IPv6 with PPPoE mode.

So the topology is like this:

ISP Gpon Router (PPPoE) -> Gpon Router Bridge mode to LAN Port 1 -> WAN Port EX511 -> EX511 PPPoE Mode (Router Mode) -> EX511 Lan Port -> EC230-G1 Lan Port -> EC230-G1 AP Mode.

On WAN settings for PPPoE, the IPv6 Address i set to auto to make it the same as the ISP Gpon Router, enabled both NAT and Full Cone NAT, and i entered a custom DNS 1 and 2 for both IPv4 and IPv6.

On LAN settings, I enabled the DNS 1 and 2 for IPv4, but on IPv6, i set it to RADVD mode + RDNSS enabled (ULA not enabled because idk what is this), With Delegation Type Prefered (not static) and the WAN for IPv6 is set at the WAN i created.

The question is, how do i set LAN (not WAN) Static DNS for IPv6 LAN just like IPv4 LAN that i can enter gateway and set static DNS? The other mode for IPv6 LAN is DHCP mode, idk if it will helps..

Hello, i currently have a Colorful iGame GeForce RTX 3060 Ti Ultra OC-V (Non LHR, early 2020 model i guess? 3 Pcie Power plugs), and i have a problem with updating the firmware to support resizable bar.

Basically, this card was my friends card, and it performs wonderfully at any scenario. However, i noticed that the Resizable BAR isn't enabled yet, so i went to the bios to enable both above 4g decoding and resizable bar, since CSM is already off from the stock config. After save and exit, booting to windows, the Resizable is not even enabled. So i suspect that this has something to do with the vbios being old (i think this was early 2020 3060ti, where resizable bar hype weren't a thing back then?), i checked HwInfo64 -> Bus -> PCI Bus -> find 3060ti and open it, and sure enough, the BAR1 size is 256MB max.

So i went to colorful own website to check the firmware update, and sure enough, there is 2 of them, and so i downloaded the 2 of them just to be sure if one couldn't update, the other one could, and when i run it as admin, it wont update and i got the error "Unsupported by this tool, contact card vendor". I ran the 2nd tool downloaded, and it results the same.

So i am here to ask for help, for someone with the same gpu (or even the same VBios ver), who has successfully updating the firmware and get the resizable bar function to run, could you please share the dumped vbios of that Rebar-enabled/updated vbios, or if anyone with the same gpu model as this one ever got the same exact error, got an updated tool for this card, could you share that with me?

Thank you in advance 😄