u/KtosKtos123

Hello, so i dont know which one should i pick, i use the ebb36 v1.2 input sharper and i wamt to go from stealthburner tap to eddy anthead without chains so my toolhead will be lighter, and also i started thinking about getting lighter x gantry, and i dont know which one to pick, the diffrence is around 15$ in my country, can anyone help me? Thanks! (voron 2.4 r2 350mm)

Hi, so i built a voron 2.4 r2 350mm with can and tap, and homing works perfect but when it comes to Quad Gantry Leveling qgl, it cannoth get thru it, the probe on some points show big tolerance diffrences. Like on video, Can anyone help? I was thinkg its something with z motors and i have unscrewed every z shaft and got it back togerher right and it wasnt it, my z belts are tighted good. Thanks so much!!! <3

hello, so in kinda new for klipper firmware and vorons, jst built my first voron 2.4 r2 350mm with voron tap and can bus ebb36 v1.2, and for some reason my voron tap isnt working, when im pulling it up and down the led on opto tap isnt changing to red as it should be (video) and when i do g28 in console, toolhead jst ceush into pei ignoring bed. Im using for it pb6 pin for signal from optotap, and when i have ! before ebbcan:... it says its always open endstop, but when i delete the ! before ebbcan:... it says its always trigged. Can anyone help??? i think i tried everything... even tring other cables... Thanks so much!!! <3

(im 16, and i never used klipper, its my first time with it)

&#x200B;

Thats my g code:

[probe]

pin: ^!EBBCan: PB6

x_offset: 0

y_offset: 0

z_offset: -0.1

speed: 10.0

samples: 3

samples_result: median

sample_retract_dist: 3.0

samples_tolerance: 0.006

activate_gcode:

{% set PROBE_TEMP = 150 %}

{% set MAX_TEMP = PROBE_TEMP + 5 %}

{% set ACTUAL_TEMP = printer.extruder.temperature %}

{% set TARGET_TEMP = printer.extruder.target %}

&#x200B;

{% if TARGET_TEMP > PROBE_TEMP %}

{ action_respond_info('Extruder temperature target of %.1fC is too high, lowering to %.1fC' % (TARGET_TEMP, PROBE_TEMP)) }

M109 S{ PROBE_TEMP }

{% else %}

{% if ACTUAL_TEMP > MAX_TEMP %}

{ action_respond_info('Extruder temperature %.1fC is still too high, waiting until below %.1fC' % (ACTUAL_TEMP, MAX_TEMP)) }

TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={ MAX_TEMP }

{% endif %}

{% endif %}

&#x200B;

&#x200B;

Hi, im in this community for like 3-4 yrs, 2 months ago i found Blocktify, and its working so good, never got acc banned amd everything works very well, unlimited skips and u can play what u want!

Tutorial:

on our web install this https://chromewebstore.google.com/detail/spotify-ad-blocker-blocki/nfmlkliedggdodlbgghmmchhgckjoaml

and then go for spotify.com

log in and enjoy!

working only in web but better than spotifuck (im using Blocktify only on my computer -windows, on my phone i use spotifuck and it has ugly gui but works for 1 year)

Have fun!

Hi, so im ending my voron 2.4 r2 350mm build, but the last thing that is canbus i could figure it out, on my board i have rj11 port which are named "can bus"( maybe photo will help), but i dosent know how should i connect the 4 wires from ebb36 v1.2 to it, can anyone help pls? Thanks! (Sorry for my english ;) )

Hi, i started building voron 2.4 r2, but... idk if my ac socket is rigt? in manual its looking diffrent, how can i connect it? Should i look for other socket? THANKS!!! <3