Hiánypótló figyelemfelhívás. Persze jön a mondás, hogy "akkor mégis hova parkoljak?". Hát egy utcával odébb, kettővel, hárommal, és így tovább. Aki autóba ül az számoljon vele.
Én, amikor végigparkolják a kerékpársávot akkor szépen behúzódom az autósáv közepére és nem sietem el. Akinek meg gondja van, rámutatok a parkoló autókra "mégis hol haladjak?".
Hi All,
I got a 1378710 membrane (rubber dome) model m. I would like to clean its keys so i can clean them better. Per kb page image the switch type seem to be removable though mine seem to be quite stuck and I did not dare to forcibly pull.
Is it possible that this board's keys (stems) are not removable?
Volt régebben egy telefonos hangfelvétel amiben Debrecen Kabar u 13 alá bejelentették (hibabejelentő, nem tűzoltőság) hogy "ég a doboz, ég a ház". Most üres telek van ott google maps szerint, korábban régi épület. Tud valaki valamit?
silly me, i only took the photo after cleaned out already. i wrapped a wet wipe around a plastic card and that's how I managed to get the dirt out (that vacuum could not suck). it was difficult and awkward though. compressed air could also work.
any other ideas , tricks to get it clean easily?
This is a 1987 Model M SSK. I am on a project to make this board more office friendly. I have already performed floss mod, however the spacebar (still) does this ominous rattling on key release. I am not talking about the click that the spring normally makes. But it's somehow as the bar of plastic resonates or vibrates on top of the flipper or so. The metal "stabilizer" rod seems to be in place and tucked inside the plastic hook on the barrel plate. This rattling also occurs as one gently prods on the side of the spacebar (without actually triggering the key). I made an audio recording though this is nothing special in terms of model Ms i think. https://drive.google.com/file/d/18k0pIpz61hSKPNEs5RngEuO7ALjpsZ8u/view?usp=sharing
I am about to perform floss modding but cannot find proper guide. I understand that one has to insert a small thread of floss vertically into the spring but it is unclear how that's done: tuck it from top or pull the spring out and put them back together? I fear that if i pull the spring off then i might not be able to get it back on.
Local store did not have flat bolts in requested size so I went with 2mm longer countersunk screws, washers and nuts. Did not think much about it. The board seems to work just fine. However, as I asked Gemini whether this was a bad idea , it says it could crack the plastic on the long run. I still think Gemini is wrong. Thoughts ?
I would like to bring an item (it its original paper box) and it fits the dimensions of a "trolley bag" of a priority ticket. It is a regular cardboard box though. Can i bring it aboard like that despite it is not a "bag"?
Also: can they bring it to cargo if out of space?
No particular question but just leaving this info here.
Some users complain about kernel panics after they installed kernel 7.x. I wasn't aware but as I now checked on my kernel version (`uname -r`), turns out I already have 7.0.0-28 installed. It works just fine on my super old Lenovo x200. I don't even know how this got installed because I heard that one has to explicitly ask for the installation of this version which I did not do. The only significant upgrade I did was when i upgraded to Mint Zena. However, per gemini that does not upgrade the kernel either. I usually install whatever upgrade manager offers in its usual list.
Sziasztok! Mikor van fehérváron a pelikán udvarban a harangjáték?
Hi all! I'm looking for a travel bag for my Model M SSK. The dimensions are one thing, but I'm hoping to hear from people who have actually found a bag that fits it well and is practical for travel.
Any recommendations or firsthand experiences would be greatly appreciated!
Region: EU