u/gsmarquis

At one point I had an easy manage agile switch in my site. I have removed them with forget controls. The site type in global will not let me drop the easy manage device types. I do not have anything easy manage.

I have rebooted, cleared out any orphaned network devices that may have been downstream of the easy switch, and check ACL, profiles, port profiles, rates, etc. I see nothing that could have been tied at all to the easy switch.

How to drop easy types from a site. Its just greyed out with a checkmark.

OC220, ER7206, SG3428XPP-M2, SG2218P, SG3428X

I have 4 vlans. One i setup to a single port with Internet access only. ACLs block inter VLAN traffic from that single vlan to rest. I setup a vpn client for that single vlan. All that works. Now I want to setup a kill switch so if the VPN gets disconnected no Internet wan traffic can happen to just that vlan.

Using policy based routing, I can only select wan ports not the VPN as the interface.

I planned on using ACLs to permit the VPN interface and deny all others so if that interface goes down the Internet stops.

Any suggestions?

I dont see any ways to setup virtual wan ports either.

OC220 controller latest stable

ER7206 router latest stable firmware

SG3428X 1.3 latest stable

SG2218 2.0 latest stable

SG3428XPP-M2 1.20 latest stable

I have 4 vlans. One i setup to a single port with Internet access only. ACLs block inter VLAN traffic from that single vlan to rest. I setup a vpn client for that single vlan. All that works. Now I want to setup a kill switch so if the VPN gets disconnected no Internet wan traffic can happen to just that vlan.

Using policy based routing, I can only select wan ports not the VPN as the interface.

I planned on using ACLs to permit the VPN interface and deny all others so if that interface goes down the Internet stops.

Any suggestions?

Been running a HT802v2 for a few years. Voip line still works and shows registered with provider. Can not get local access to the gui. Does not ping. IP/Sub tripple checked and is correct.

Changed ports. Not vlan, acl or segmentation related. Rebooted.....nothing.

I can SSH into it.

My network is all Omada Access level equipment. I have 3 APs, 2 celling and 1 wall all hardwired to poe switch. The mesh option is not on. The APs insist on joining with a mesh config. I have removed all of them and re-adopted. I have rebooted the controller and APs. The cable runs are solid and test fine.

If I remove and only adopt any 1 AP the uplink is the lan I have them on. If I adopt the celing mounts first, they stay non mesh with the lan uplinks. As soon as I adopt the wall AP, they all join mesh. The wall AP has additional physical ports which stay connected so the cable run is being utilized.

I have turned LLDP on and off with reboots.

What am I doing wrong here?

Everything is on the latest stable firmware.

The last handful years this is my setup.

OTA Antenna in attic - $0 month after investment of $250 for antenna, mount, rg6, dis amp for 5 locations. Nets 65ish channels.

FIOS 300/300 - $20 a month.

Self managed VOIP line for house - $0.89 a month.

I moved to a MNVO cell provider to drop $100 a month down to $30 a month. It added a $15 discount to my FIOS home internet. I cant see how to drop my monthly connectivity any further. The FIOS internet also comes with reward bucks you can use to pay for streaming service which I never started. The only one that would be free with the internet is HULU/D+.

I also use free IP services like Pluto, google, and Tubi.

No data will load when LTE signal is good. As soon as I move and get 5Guw signal everything is instant.

I have gone through two rounds of visible tech support.

I have factory reset my phone.

I have switched from esim to psim.

Nothing. LTE is not functional for data. Calls go through, texts eventually make it to wife.

I just paid for another year of visible plus or I would port out to another provider. I was told visible will not refund.

Most of my signal in my daily routine is LTE.

What am I to do?

I have been running an A139 Pro 2 ch hardwired for about 3 years now. Randomly the announcement of two channels recording sometimes happens several mins after I started driving rather than a few moments after I start the car.

I have updated firmware, formatted SD, and defaulted the settings.

Should also mention I park in garage at home and at work. Most of the time no extended direct sunlight.