u/luvmehatemefme

I think I need to add a carry wheel gun to my collection. Im having trouble deciding on the 856 UL or the 605 poly protector. Any advice??

I have MP40c that i swapped a 4" 9mm barrel in and it runs fine. I recently got a 4.25 barrel and tried it in my 40c and it fits in fine but when you rack the slide. The slide sticks in the rear position. Is there something you have to mod in order for it to work? Or does the 4.25" barrel just not work in the 40c? Ive tried 2 different 4.25 barrels and they both do the same thing.

So you guys got me to cave and Im looking for a a new or used hunting bow.

at least 70lb max draw

30" draw length

ATA 30"-32"

Less than 500 bucks bare will go Max of 700 if its i hell of a deal.

I have a line on a few Used Hoyt Torrex XT for 300-350. Im also Seen a new Bear Adapt 2 that fit the bill for like 700 RTH. Also a regular Torrex new for 500. Anything wrong with those bows? Anything else similar that i should be looking for on the used or new market? Ive been learning for a few days now and my head is spinning. So many to choose from! TYIA!

So im newish. Last year was my first year white tail hunting. Im using a mid 90's Bear compound. Draw weight is 55lb. I run X5 blackout 340 spine arrows @ 435 grains. I push them at 205 FPS. Recently i got my bow dialed in (fletchings were hitting ) and im finally getting decent. I tried moving to the big boy range that goes out to 100 yards but on my sight I cant get my pins low enough to get further than 50 yards.

So Im in need of some new arrows for hunting and Im trying to decide whether there is a reason to switch arrows?

Do people have lighter target arrows they use and different ones for hunting?

Do i need a different type of sight to shoot further.

I have an MP 1.0 with the 1.0 trigger bar and the 2.0 sear housing Without the sear actuator. I had to adjust the trigger bar but beside that its ran 100 round flawlessly. Most things I read online say this setup wont work. Is there any mechanical reason why I shouldnt run this set up? I know the trigger will be better with the full 2.0 trigger bar and sear actuator.

Lets say you adjust the powder charge accordingly and all have the same chamber pressure. As long at its with spec and the projectile isnt contacting the lands, Does OAL matter in terms of accuracy? Not enough to be concerned about?

I dunno WTH is going on this. Its gotta be something stupid. How do you install the ejector into mp 2.0 sear housing? Got a MP 2.0 sear housing installed all the parts. Oops it takes a different ejector than the 1.0. Buy wrong ejector. Bought the shield 2.0 ejector. So i buy the right one now. Try to install it and it wont just slide it. Ive tried all kinds of angles. I try a lil force but nothing. I line it up the the Shield 2.0 ejector and it looks very close if not the same.

So I just got done loading over 1000 556 rounds and it was damn near perfect throwing charge with the ball powder. I switched over 9mm and I cant get the rotor to fully rotate. Ive had this problem since I bought it with 9mm specifically. Im using the case activated set up with the PTX . the die bottoms out on the shell plate but the rotor is like 1/2" from fully rotated. Any ideas whats going on here? only thing I can think of is to 3d print a small spacer to get it fully rotating but this thing should work right from the factory without the mods.

I already have 9mm dies. Im reading that people prefer the Undersize .380. Is this correct? Should I just get the regular .380 dies? Or just pick up the .380 undersize die and the .380 FCD? Ill be loading for an LCP max if that matters.

Has any has success with the Lee bullet feed die set up for 223?

Ive played with this thing many hours and itll work fine for 10 and then one projectile will get stuck. next time around same projectile will go though with no problems. Using 55 gr FMJ

So I was looking for a bolt action over the weekend and was gonna pull the trigger on a Howa when i saw savage have a rebate 75$ off the axis 2. Shit 325 out the door then minus a rebate what the hell Ill grab one in 308. Went to go and buy it after work today and now EVERY website has them for $400+. Rebate started on May 15. Sounds like some shady business from Savage.. Fuck Savage Im buying my Howa. And While Im at it Fuck Springfield as well!