u/Most_Conclusion2522

So I Installed a new OEM steering wheel from an EP3. However, I think I did it wrong. When I removed it the steering wheel was at +45 degrees. When my brother installed back he centered at the clock at the middle. Now the steering wheel is towards the left when the wheels are straight.

What should I do here. Is there a way to know which is the correct point to installed back.

https://preview.redd.it/7w9x5dcfimjh1.png?width=508&format=png&auto=webp&s=6b6cbac7be923fc28b2bb155f4111821c3204276

Here is a picture of how it looks when the wheels are pointing straight.

EDIT/UPDATE

I followed the instructions of the Hemls manual and the steering wheel was slightly pointing counterclockwise. I just took for an alignment and now is straight.

I applied for sentry a few days ago and 2 days later I was already conditionally approved. However, I've lived in the US with my uncle during all my high school years. Since then I've been living in Mexico and crossing everyday to work and college.

In my application I mentioned I've been living in the US since 2020 when I started high school. How should I go about this? Should I mentioned this if asked? should I changed after if being approved? please share your own experiences. My mother is Mexican but I haven't done the process for Mexican citizenship.

I don't wanna have any trouble in my interview tomorrow for a dumb mistake

Thanks in advance

Hello everyone this is my first post here. I hope I can have some guidance here.

So I've been in this job since June of 2023 working as a W2. In January of 2025 I left this job for 6 months, and I came back on September of last year. The rehire process was quick as they already know me. They only mentioned my schedule and pay rate (which was only 50 cents more). So the first week I received my first "paycheck" they basically just send me a Zelle for the amount of hours I work.

Anyways I needed a job and didn't complain by then. However, I started researching on my own; and I found out that I am not being correctly classified. I spoke with them yesterday. and I feel they gave this BS in which why 1099 is better for them and me. "You earn more, and will pay less taxes." I am not a tax expert, but I feel they are trying to get away with their duties/payments.

I am just a 21 year old with no depends. Putting aside that I am being misclassified. I don't think I can have tax reductions because 1: I don't have dependents and 2: I am really an employee not a contractor.

I have to take a decision soon.

Hello, all a few weeks ago I got this light. It all started one morning that I drove my brother to his job. He had his lunch on top of the passenger dash air bag. Not sure if this is the root of the problem. I've read some mix opinions on the internet. Another think worth to point out is that my ground that goes from the ABS module to the engine mount is not properly attached as the bolt was stripped.

It could be that he unbuckle his seatbelt and he was still in the car and the sensor detected it. This is the ONLY light I have on the cluster (besides my CEL hehe). I don't have the infamous SRS light.

Please share any experiences.

Hello, all a few weeks ago I got this light. It all started one morning that I drove my brother to his job. He had his lunch on top of the passenger dash air bag. Not sure if this is the root of the problem. I've read some mix opinions on the internet. Another think worth to point out is that my ground that goes from the ABS module to the engine mount is not properly attached as the bolt was stripped.

It could be that he unbuckle his seatbelt and he was still in the car and the sensor detected it. This is the ONLY light I have on the cluster (besides my CEL hehe). I don't have the infamous SRS light.

Please share any experiences.

Hello everyone,

Trying to reduce the sloppiness of my OEM shifter. I already replaced the 2 bushings that go in the shifter and they worked great. But when comparing to other stock RSXs it still feels loose/sloppy. Has anyone tried just using acuity shifter bushings with the stock shifter?

Please share any feedback on this.

P.S. No i don't have 500 to drop on an Acuity shifter.

Front passenger side tire Acura rsx

First post I do here. Enjoy!

https://preview.redd.it/dtiuuxkg2t0h1.png?width=1156&format=png&auto=webp&s=6bcf93c38ff74bd3c29cae369ad5e8a7ca938ec7

I've been thinking of changing my type R rep shift knob for a OEM TSX secondhanded.

Is anyone here running this combination? I would appreciate any pictures.