What do you know puts you on tilt first round?

There's a lot of stuff in this game I find a bit frustrating, like players opening up what I call "YouTube angles" during prep and then just abandoning them for me to get picked from, or having the bottom of the leaderboard instant pick case and then go on a journey

But I think the only thing that can happen round one that gets me completely malding is getting spawn peeked or having someone do a crazy run out on me

What about you?

reddit.com
u/BrightFallsCoffee — 9 hours ago

Literacy situation is making online spaces feel pretty lonely

I hope no one takes this as me acting like I'm a big time high performer and no one can compare to my le epic vocabulary and whatever - I'm a normal person who likes to talk online with people about the stuff I'm into, and that's been a pastime of mine for around 12 years or so

I guess I would just say that as opposed to an introvert/extrovert thing it's just nice to have human discourse on demand - if a movie or a book or or something else gets my brain going and I want to talk about it, for over a decade of my life I've been able to just snap my fingers and have some people to discuss it with and that's really nice

But lately, especially the last 6 months or so, I've noticed that its upsettingly hard to get a good chat going, it seems like usualy you have to retread your point a few times for some people to get it, or worse people just don't understand and refuse an explanation and debate you on a point you were never trying to make in the first place. The worst is how often someone will look at a post longer than a few sentences and just say "its not that deep 😂😂😂" as if it's embarrassing to have thoughts about the world

Anyone else getting this? I worry I'm coming across as if I'm putting people down, and I want to clarify I don't have any disdain here, I genuinely find it really unfortunate that some people who clearly want to engage (otherwise why would they be on niche topic subreddits?) have just not been equipped with the tools to understand and communicate properly

reddit.com
u/BrightFallsCoffee — 9 days ago

Put Pressure on Lego

At the end of the day the only way to coerce bad actors to behave is to make sure they lose more than they gain - it doesn't seem like BAM corporate really cares that individual franchise owners are bearing the repercussions of their actions, but if Lego was pressured into re-evaluating their relationship with BAM as one of their authorized resellers, things might improve (quickly)

Lego's "Contact Us" page

reddit.com
u/BrightFallsCoffee — 1 month ago

Does Premium BP / Monthly Membership give permanent access to the BP Operator?

As in title, if someone buys the current premium battle pass or gets access to it from the monthly membership, would they get Snake only for the duration of the pass/membership or does it persist if you cancel the membership or play into the next battle pass?

reddit.com
u/BrightFallsCoffee — 2 months ago

Loose Threads in Overhangs?

Printing on a P1S, Bambu Matte PLA, 200C hot end and 55C BIQU plate

Lately I've noticed anything I'm printing something with overhangs, it has these loose threads of filament along the underside (photo is from a slightly below angle, looking up)

They're loose enough that I can catch them with my fingers and tug them down / snap them

Any way to prevent this?

u/BrightFallsCoffee — 2 months ago

Very new printer (both me and the device) have around 250h of prints over 3ish weeks with a Bambu P1S. All prints have been great until the last three or four had similar failures to above so I started doing some troubleshooting

Settings for this specific print were;

0.4 nozzle, 220C and 55C bed, textured plate as you can see, Bambu PLA used

Fixes attempted so far;

Washed the plate, checked the nozzle wiper, checked nozzle for clogs, did a full calibration in Bambu Studio, and did a flow rate calibration (which is what failed here)

Other notable info;

I do have an AMS, there's about eight dessicant packs hanging out in there and whenever a spool leaves the AMS it goes into a freezer bag with a dessicant pack as well. Ambient humidity is around 25-35%, I recently tried my first two non-Bambu filaments (an Elegoo PLA silver and an Elegoo PETG black) which printed fine but only shortly thereafter did I start having issues

u/BrightFallsCoffee — 2 months ago