▲ 1 r/CPAP

Any Suggestions?

I’ve had my device for two weeks and have had zero nights of being able to wear it. I put it on and try to relax, but within ten minutes I’m taking it off. The main issue is it completely closes off my nose. It’s a full face mask, so once it sits in the bridge of my nose, I can’t breathe through it anymore. Has anybody else experienced this and if so how did you get over it?

reddit.com
u/DamianP51 — 15 hours ago

$3.00 Cards For Sale

Just trying to thin out my collection. Will mail in plain white envelope each card in sleeve and top loader.
$3.00 each.

u/DamianP51 — 12 days ago

How Dumb is Artie?

Was this guy suppose to be comic relief, or a tragic charactor Tony had to look over since they were friends since childhood?
I'm rewatching the series and just watched the episode where he proclaims to Tony he's in love with Adrianna, then takes her out to dinner because she's quiting. He spends the entire scene holding her hand making comments about her upcoming marriage and how he is going to miss her. The scene is so cringe to watch because he seems so clueless. Adrianna keeps pulling her hands away and he keeps grabbing them.
Both sides played the parts really well. Drea especially.

reddit.com
u/DamianP51 — 14 days ago

Odd Repair - Need Some Opinions

2019 Nautilus. I've posted in numerous threads about the massive issues I've had with this vehicle since purchasing it three years ago.
Last year I noticed in the spring the rear window washer wasn't shooting water anymore. I just sort of dealt with it until the front washers start crapping out. Got it to Ford just two months ago, they came back with old/brittle lines, I approved the repair and they were replaced.
$200 repair but okay, off I go. Within a couple of weeks it started crapping out again so I reached out to my service rep, he said bring it back in.
Because of life it took me until this past weekend to get it back in. They checked it and found all the lines and the nozzles were gunked up with a gooey sludge. The repair would be $280.00 for new nozzles and the lines and pump to be flushed.
He asked me what type of washer fluid I use and who puts it in which I found odd. I know how to put washer fluid in and I use the same stuff everybody else does. Gallon jugs of the green or orange stuff you get at any store.

Is there some magical Lincoln only washer fluid I'm suppose to be using, or does this gooey sludge story sound like complete B.S.? I've owned cars since 1985, never had a problem with washer fluid lines gunking up.

reddit.com
u/DamianP51 — 22 days ago

Not Able To Print Anything It Seems

The green is on my AD5X, the brown is the 5M. Both are standard PLA filaments. Both were dried for six hours yesterday.
Both build plates have been cleaned and had glue applied prior to printing.
Both fail every time.

I'm just trying to print this Yoshi I found on makerworld
https://makerworld.com/en/models/538452-yoshi-and-egg-multi-part#profileId-455628

I so far managed to print his nose an arm and the egg. The brown were his shoes, the green was his body.

Not sure what else to change at this point. I'd hate to give up, I need to learn how to fix these things for future prints.

u/DamianP51 — 26 days ago
▲ 134 r/hairmetal

Grammy Museum 80's Rock Exibit

Went to the Grammy Museum in Clevend, Mississippi yesterday. They are currently running an 80's Rock Exhibit. Here's a few pics from it.

u/DamianP51 — 1 month ago

Printing Different Parts In Different Colors - Same Print Time

I have the Flashforge AD5X and I want to run a print of a few different pieces, that are themselves each different colors. So one piece is green, another white, another red.
Instead of printing each in their own seperate print run, can I set a single print to print each piece in their own assigned color?

reddit.com
u/DamianP51 — 1 month ago
▲ 35 r/rush

Detroit this August.

I've seen RUSH multiple times through out the eighties back home in San Francisco. My wife surprised me with VIP tickets to their show in Detroit this August so I can fly up and take my daughter to see them for her first ever arena show. I can't WAIT! Gonna be a fantastic weekend!

reddit.com
u/DamianP51 — 2 months ago

How To Scale Down A Multi-Part Print

I want to print mini versions of all the various Star Wars helmets to display. There are an abundant number of plans online. I want a multi-part print so I can print all the colors seperatly but almost all of the most detailed plans I find, are wearable. I want to scale them down to only be about 6" in height.

What is the right way to scale down a multi-part print that ensures all pieces will still fit together?

reddit.com
u/DamianP51 — 2 months ago
▲ 11 r/KISS

Destroyer 45th Anniversary Remastered

I'm listening to this on Apple Music right now. What's so different from the original version of the album? Aside from every damn song panning the vocals left to right, are there any other real changes?

reddit.com
u/DamianP51 — 3 months ago