Buy Quality 7.3 Parts
Where is a good site to purchase parts for a 7.3 Excursion ? Im seeing ebay and other diesel sites along with local autoparts stores.
Thanks
Where is a good site to purchase parts for a 7.3 Excursion ? Im seeing ebay and other diesel sites along with local autoparts stores.
Thanks
I recently purchased a 2001 Ford Excursion with the 7.3. After reaching 60mph+ It dies and I had to pull over. It started back up and runs good but only under 60mph.
I took it to a auto parts store for code reading and it read 3 codes.
P1210
Injector Control Pressure Higher
Than Desired (Engine Off)
P0475
Exhaust Pressure Control Valve
P0705
Transmission Range Sensor
Circuit
I did take it to a shop to get the seals around the HPOP replaced since it was leaking alot of oil. It did die before taking it to the shop. I replaced the CPS Sensor myself. Im going to do some research on my own but wanted help if any of these codes could be the problem and if its something simple to fix.
Thank You
I recently purchased a 2001 Ford Excursion with the 7.3. After reaching 60mph+ It dies and I had to pull over. It started back up and runs good but only under 60mph.
I took it to a auto parts store for code reading and it read 3 codes.
P1210
Injector Control Pressure Higher
Than Desired (Engine Off)
P0475
Exhaust Pressure Control Valve
P0705
Transmission Range Sensor
Circuit
I did take it to a shop to get the seals around the HPOP replaced since it was leaking alot of oil. It did die before taking it to the shop. I replaced the CPS Sensor myself. Im going to do some research on my own but wanted help if any of these codes could be the problem and if its something simple to fix.
Thank You
I recently purchased a 2001 Ford Excursion with the 7.3. After reaching 60mph+ It dies and I had to pull over. It started back up and runs good but only under 60mph.
I took it to a auto parts store for code reading and it read 3 codes.
P1210
Injector Control Pressure Higher
Than Desired (Engine Off)
P0475
Exhaust Pressure Control Valve
P0705
Transmission Range Sensor
Circuit
I did take it to a shop to get the seals around the HPOP replaced since it was leaking alot of oil. It did die before taking it to the shop. I replaced the CPS Sensor myself. Im going to do some research on my own but wanted help if any of these codes could be the problem and if its something simple to fix.
Thank You
I recently purchased a 2001 Ford Excursion with the 7.3. After reaching 60mph+ It dies and I had to pull over. It started back up and runs good but only under 60mph.
I took it to a auto parts store for code reading and it read 3 codes.
P1210
Injector Control Pressure Higher
Than Desired (Engine Off)
P0475
Exhaust Pressure Control Valve
P0705
Transmission Range Sensor
Circuit
I did take it to a shop to get the seals around the HPOP replaced since it was leaking alot of oil. It did die before taking it to the shop. I replaced the CPS Sensor myself. Im going to do some research on my own but wanted help if any of these codes could be the problem and if its something simple to fix.
Thank You
Does any know how to clean up an internal corner on V-Carve using a 2D drawing. I circled the Line I want to use on the right. The profile is what I circled on the left. It needs to trace on that line and ramp up at a 45° Angle. I just don’t know how. Im using a 90° bit.
I Recently bought a 2001 Ford Excursion with a 7.3. Previous owner told me that the HPOP Gasket and Reservoir need to be replaced and gave me parts. It does leak oil. I don’t have that much experience working on engines, so I was wondering if it would be worth for me to work on it myself. Ive seen videos on YouTube but would like advice from people who have worked on it to see what I can do or if its better to hand over to a shop. And what steps I need to take if I were to start taking it apart
Thank You
I Recently bought a 2001 Ford Excursion with a 7.3. Previous owner told me that the HPOP Gasket and Reservoir need to be replaced and gave me parts. It does leak oil. I don’t have that much experience working on engines, so I was wondering if it would be worth for me to work on it myself. Ive seen videos on YouTube but would like advice from people who have worked on it to see what I can do or if its better to hand over to a shop. And what steps I need to take if I were to start taking it apart
Thank You