u/FreakyOne87

I received this mail after the lawyers office was already closed, so I can't confirm until tomorrow, but I figure you guys would likely be able to lead me in the direction I need to know.

I filed chapter 7 and had the MOC in March and it was entered and known that I wanted to reaffirm on my cat loan as it's the only car I have that's reliable, so I open to reaffirm instead of letting it go and doing promise to pay. Well today I get this letter in the mail and I assume it's one of three things, t

Them making sure that the reaffirmation agreement is the way I wish to go, even tho as far as I know even my credit union has already heard back from the courts and I'm in the system as a reaffirmation. Or denial of my request and charging the car off, or just approving it.

So which do you think it is ?

_________________________

consider and act upon the following:

Reaffirmation Agreement filed by Creditor Superior Choice Credit Union

Motion for Approval of Reaffirmation filed by Debtor

and other reaffirmations that may be entered into prior to the reaffirmation hearing date and filed with the

Court prior to or at said hearing.

The debtor(s) must appear at the hearing TELEPHONICALLY; however, counsel at the hearing TELEPHONICALLY; however, counsel for debtor(s) is NOT required to appear. Parties should call in ve (5) minutes before the Istart time of the hearing

using the information below:

Dean M Lugge Clerk, U.S. Bankruptcy Court

IF A PARTY FAILS TO APPEAR IN PERSON OR BY COUNSEL THE COURT MAY PROCEED WITH THE SCHEDULED HEARING AND MAY ENTER AN APPROPRIATE ORDER OR JUDGMENT INCLUDING DISMISSAL OF THE PENDING MATTER.

Carrying of firearms is prohibited. Section 65 of the Illinois Firearm Concealed Carry Act prohibits a concealed carry license holder from carrying a firearm on or into any building/property under the control er the control of a federal government or

the courts.

Hszørdons road conditions may necessitate canceling scheduled hearings. When applicable contact the Bankruptcy Clerk's office.

Okay, I keep seeing a debate and I wanted to ask, even tho I'm sure the difference is very negligible, but it's got me wondering.

I have a 9950X3D2 dual vcache and CCD, I am on a 4DIMM, but an able to run either of these.

I haven't completed all the timings and such but the initial part of these passed a decent amount of stress test with everything loose.

So which would be better to pursue, if it even matters?

48GB CUDIMM KIT (V-Color) on a 4DIMM x870e Dark Hero:

DDR5 8200 2:1 CL34 GDM OFF Nitro 1/3/1 FCLK 2200

Or

DDR5 6400 1:1 CL26 GDM OFF Nitro 1/2/0 FCLK 2200

I can boot 6600 but as soon as I run and tests the whole PC freezes so I've settled on 6400 for the 1:1 profile.

Okay just doing some quick boot with stock timings but messing with voltages, I can boot on my 4 DIMM 8400/2200 GDM on 2:1 I assume. But I can also boot 6600/2200 gdm off 1:. Which profile would most benefit me for AM5? I assume my IMC is decent being able to even boot 6600 in 1:1 at 2200. But idk what profile will benefit me more in the long run to go ahead and start messing with timings.

Okay I was in the middle of using the firmware update tool on my monitor, from within Windows with it direct connected. Well I guess why I was updating my PC installed a GPU driver and my monitor flickered and turned off, and hasn't came back on while in Windows, the software was still running in the background at the time of the flicker. So idk if it's still running or not, and if not, how do I hopefully unbrick my monitor, It's a PG33UCDM3 🤦.

Okay this is a brand new cablemod cable and the wire view hooked to my GPU. These definitely seem a little too close for comfort, at least the two outside pins do, under 600w load of furnark they are always sitting at around 9.0-9.2 with the latest being around 7.8 so that's a difference of 1.4-1.5a 😭.

Okay this is going to sound dumb but I forgot how it came installed in the box, as I got one with the new quick mount frame. But which direction is the block installed? It's got two different sized flow paths, one wide and one very narrow. Which one is supposed to be the inlet? The wide opening or the narrow opening lol.

Okay, I've got the AM5 heatspreader installed and I purchased the offset and mounting kit, so can you use the offset kit and regular mounting together to be able to install the cooler offset and 2mm lower? The instructions say nothing about how to use it when you have the AM5 heatspreader installed.

Olay I'm not use to building in SFF cases and I'm helping a buddy put a small CPU only loop in his Corsair 2000D. I have tubing and fittings already but looking for the best bang for your buck, easy on the wallet combo of pump/res and radiator for an SFF build. I'll have the CPU block covered, just looking at guidance on the best money saving value for the 3 components.

Okay when the AM5 heatspreader comes back in crock I plan to buy one, and use it with my ryzen 9 delidded, with my 360 thermalltake aqua AIO. Will I need the offset and mount kit with the AIO with the heatspreader or will it work without the kit?

Okay, I'm upgrading my current setup that is a direct die cooled CPU, and I'm going to be giving it to my buddy, I still have the original IHS and everything, so I was wondering if it was relatively safe to use ptm7950 as the TIM between the die and the original IHS? Then ptm7850 on the regular IHS. He's going to be using it with a contact frame so it's better then just trying to use the loose IHS with the stock ILM. And an AIO.