Login

u/Ok_Delay7870

r/simracing r/moza r/AMDHelp r/GyroGaming r/OrcaSlicer r/SolidWorks
Image 1 — Inverted pedals v2. Got the hardware and made adjustemnts
Image 2 — Inverted pedals v2. Got the hardware and made adjustemnts
Image 3 — Inverted pedals v2. Got the hardware and made adjustemnts
▲ 26 r/simracing

Inverted pedals v2. Got the hardware and made adjustemnts

​

https://www.reddit.com/r/moza/s/69sxI0G9Aj - link to my first attempt post.

I have found a free wooden plates near the trash bin, one almost perfectly fitted my rig width, only had to cut it a little bit.

In comparison to my previous attempt - now the height is fine, I can comfortably use it with bare feet and shoes as well and my seat doesn't interfere because of the raised heel base.

I cannot yet say for sure if this is better than F1 position I've had previously but this is definitely closer to real car, only wish pedals were better but it's what I have now and glad how it eventually worked out.

u/Ok_Delay7870 — 2 days ago
▲ 12 r/moza

Inverted pedals v2. Got the hardware and made adjustemnts

https://www.reddit.com/r/moza/s/69sxI0G9Aj - link to my first attempt post.

I have found a free wooden plates near the trash bin, one almost perfectly fitted my rig width, only had to cut it a little bit.

In comparison to my previous attempt - now the height is fine, I can comfortably use it with bare feet and shoes as well and my seat doesn't interfere because of the raised heel base.

I cannot yet say for sure if this is better than F1 position I've had previously but this is definitely closer to real car, only wish pedals were better but it's what I have now and glad how it eventually worked out.

u/Ok_Delay7870 — 2 days ago
▲ 1 r/AMDHelp

How to use iGPU for second monitor with discrete GPU installed?

https://preview.redd.it/ikwx9y0rn0bh1.png?width=379&format=png&auto=webp&s=277ac685aeb1e776853ad9530adcf61912b1b072

Hello. Is there a seperate "GOOD" driver for iGPU to work normally?

I have a B850m + Ryzen 5 7600x + Radeon RX9060xt.
I want to connect main GPU with main monitor using DP cable, and secondary monitor with Motherboard (MB) with DP cable as well.

I just went through a DDU cleanup process because I have tried to fix some issues with PC:

  1. It was flickering, not always hooking Radeon GPU at the start (PC would work on iGPU instead)
  2. It forces SolidWorks to work on iGPU only.

As soon as I reinstall GPU driver with prior DDU cleanup and dont install iGPU driver - all of this is gone, but I can't use my second monitor connected with DP to my MB.
I cant connect second monitor to GPU because it only has one DP out and my second monitor is DP exclusive.

I have tried looking for a specific driver on AMD website and also tried auto detection app and no luck. What should I do?

reddit.com
u/Ok_Delay7870 — 3 days ago
▲ 8 r/moza

I have broken my SR-Ploadcell cable and fixed it the automotive way

Often switching springs and dampeners unglued that little plastic piece holding a cable with a Z-shaped pathway. Then, a lack of hard mounting allowed the cable to slide under the pedal bracket and be bitten a few times. I used my old "experience" of fixing electrical issues with tape in my older cars as a "temporary" solution until I finally get a soldering iron, but I'm disappointed that this can happen without you knowing because you will never see what's inside unless you remove the pedal from the plate. There must be a better way, more reliable at least.

u/Ok_Delay7870 — 27 days ago
▲ 0 r/SolidWorks

Solidworks Simulation issue with joints.

Why cant I have all joints calculated correctly?

This is a post made from a 4 different configurations and for some reason some of the top ones missing connections. Manual rejoin doesn't fix anything, I guess there is some kind of count based limit but I don't understand how big it is.

There is, from physical point - nothing that make sense, because all connections are the same. Whenever I remove cut from the tubes (they extent into main poles) - nothing changes, only I get more loose ends outside. I really want to calculate this as a beam model since its very heavy for solid shell simulation.

Thanks in advance!

Middle section

Upper section

closer look

reddit.com
u/Ok_Delay7870 — 1 month ago
▲ 74 r/GyroGaming

Funny side effect of vibration with gyro

Hey! I got 8bitdo Pro 3 today. So far loving the controller but this made me worry at first, now I like it (kinda), but still wanna know how to fight this whenever I need without completely disabling vibration.

(Context:Vibration causes the controller to shake violently thus applying gyro forces)

u/Ok_Delay7870 — 1 month ago
▲ 2 r/moza

I do update PitHouse from time to time and constantly having issues with it. Like if I update base right now - I will have oscillations on my R12 in Assetto Corsa on my perfected settings.
With latest PitHouse update in AC Rally my wheel turns unnaturally to the right or left when I press the gas, all cars become undrivable, but especially FWD/AWD cars.

Is there a list somewhere, with latest stable, no-bs version of software for both PitHouse and hardware updates?

reddit.com
u/Ok_Delay7870 — 2 months ago
▲ 1 r/OrcaSlicer

What I usually get

Im loss for ideas, I couldn't find what I want in the settings....
I have this part taking almost my whole table and my problem is that hole perimeters extra adhesion skirts print before the fill of the first layer. These dots for M3 screws for example just fall off and ruing the whole thing.

Can I set it up somehow to print outer skirt, then start with filling up the shape and having holes cutouts procedurally made one by one as they go?

I temporarily fixed this by making a custom layer modificator but can I make this result embeded into global print settings?

What i need

reddit.com
u/Ok_Delay7870 — 2 months ago