u/condemned-noticer

Hello, i' looking for a solution to secure an axle actuated by a spring to a plate, it looks like that :

https://preview.redd.it/4ousgmi84fuh1.png?width=465&format=png&auto=webp&s=33f434d079b585f3ae96ac4d5cc4e88b08527169

Blue part is the plate it needs retaining to, the yellow is an empty blind cup with a hole in the center for the axle/safety pin (sorry i don't know the exact term) the orange is the axle/pin, that needs to be able to move forward when pushed upon, and is pushed back by a spring to disengage from a hole that retains it. The pin needs to be restrained both forward and back so it cannot escape the pocket and the spring pressure/pushing pressure from the back.

Does anyone have an idea of a system to both retain the cup and the pin to the blue plate?

follower

cylinder

the follower can be inserted from the back of the cylinder, but can also exit in thesame way

Hello, i'd like some help if you guys don't mind proposing ideas, because i'm running in circles here.

I want to be able to have this cylinder rotate 45° clockwise with the action of the follower moving linearly back and forth. The follower is able to move 14mm back, the external dimensions for the cylinder is a 16mm diameter and runs on a 3mm axle in the center of it. The follower has no rotation and moves only back and forth.

I would like to be able to retain the follower on the cylinder by slotting the follower from behind it and use the geometry of the camtracks (4 cam tracks) on the cylinder to insert the follower / remove it easily and using the camtracks geometry to prevent the carrier from going backward too much.
I'm going for 4 cams to follow the 4 camtracks to spread the rotational constraints.

The design can (maybe) move the cams inside the follower but i'd prefer it if it was possible to keep the cams on the front of the follower's 4 small "branches" protruding at the front.

The geometry of both the cams and camtracks can be altered, i would like the cams to remain a solid part of the follower.

Sincerely,

extended (i want to limit the extension at this point)

retracted (movement is limited properly)

Hello, i'm currently trying to design a multi-cam system, the goal being a 45° rotation when the holder is pushed forward on the axle, but i want a retaining system built in the cam track of the axle. I can only insert it from one direction, and i would like to make it self retaining by using the geometry of the cam track to insert it, turn it (maybe add a rotation limiting system in the holder?) and basically use the camtrack so the axle cannot be withdrawn as it is able to for now (you can extract it from the holder from the insertion direction, but i also want to retain the ability to isert and extract it from the holder by simply pushing/twisting it without a retaining feature integrater to the holder). Do you have any ideas, because i'm hitting a wall here?

Hello, every time i take 1000mg monolaurin, i'm crashing hard a few hours after, like, irrepressible fatigue impossible to jugulate, coma nap forced to lay down type of fatigue, there's no way i'm staying awake, and when i wake up, i feel like shit.
Anyone else?

Hello, every time i take 1000mg monolaurin, i'm crashing hard a few hours after, like, irrepressible fatigue impossible to jugulate, coma nap forced to lay down type of fatigue, there's no way i'm staying awake, and when i wake up, i feel like shit.
Anyone else?

Hello, i'm searching for the 3d files of the mannlicher M95, especially the action and the receiver, if any of you know where i could find it? I've been searching without success so far, and only found corrupted or incomplete files.

Will it ever appear in a video on forgotten weapons?

Hello
weird problem on my P07 (compact, hammer, changed the recoil spring with a DPM, used both the strong and weak spring, no change, i'll try the OG one next time i go shooting, but it started happening suddently, while it was shooting fine before, so i don't understand?), he shoots the first round when the barrel is cold in the correct point, then everything goes up 20cm and make a tight group here, just move up, not on the sides.

Tried with different ammo, different shooters, with/without the mag, (resting the base of the mag on a support to eliminate the shooter factor as much as possible, but we tried free standing, same results, with a bit more spread at 25m).

If you string shots, they all go to the up there POI, if the barrel has had some time to cool, (1min approx) he shoots center the first one then up for all following. Rinse and repeat, have done it for 3 months, tried everything but i'm at my wit's end, i don't understand why? Any idea what's happening?

Also, changed recently with LPA adjustable sights, same problem.

Hello, i'm at the end of my rope concerning lyme, i've been sick for 25 years and i'm nearing the limits of my body and mind to endure. I feel the end is nearing despite my will to fight on. Honestly, this is probably the last rope i have to reach for, since the medical community in my country refuses me any treatment while i have symptoms and serologies to prove i'm still sick, they even refuse to provide me with ceftriaxone, all i've ever had was 3 weeks of doxy.

Can anyone explain, based on experience and knowledge:

- How and why a rife / coil machine works ? I've found too many conflicting info online to know what to believe for certain. (GB4000, spoooky, doug coil?)

- If it had any positive/negative influence on you, which it was, the lenght of time it took to help, how it went, was there herx, etc....?

- How much did you pay for your machine, if you bought one, and what type, with which options, and what would you recommand?

I have 2k€ left, and that's it. Please, any answer helps.