As title states need help finding a carb for an old duratrax torq .21 nitro engine or even a suitable engine replacement unfortunately the carb on the torq 3.5 is missing a few parts cant find anything or im just not looking in the right place or possibly a 3d print to convert it to electric
as stated trying to find a video or someone who has even an image of the location of the bank 2 vvt solenoid as it has failed on my car ive tried finding a video but nothing shows up sadly
got the car for a steal (900) runs great and all but uses fuel like no tomorrow frankly i dont want to take it to a shop as i dont have the money for that as well i live on a very tight budget
As title implies my nissan has a hesitation when accelerateing from a stop however drove so I'd say the transmission is fine as when I bought it I did do some tests before fully buying it. It acts as if it went into a limp mode for a few seconds and has a p0507 code that it got recently (same day) only things ive done was change an air filter as it drove fine before I changed the air filter
As title implies my nissan has a hesitation when accelerateing from a stop however drove so I'd say the transmission is fine as when I bought it I did do some tests before fully buying it. It acts as if it went into a limp mode for a few seconds and has a p0507 code that it got recently (same day) only things ive done was change an air filter as it drove fine before I changed the air filter
Bought car recently for gf an im currently trying to fix the small issues like the glove box and so on unfortunately I dont know what the part exactly is if someone has a 3d printable file of the part that would make it easier for me to repair it over buying a new one unless I can find it decently cheap
84 s10 with 88 s10 engine (v6 4.3) stalling under load what should the fuel pressure be when under load? And second issue is it runs poorly when map sensor vacuum line is connected but runs fine when not connected (still stalls under load) not sure where to go from here just at this point trying to get her to stay running is getting harder and harder (parts i have replaced fuel pressure regulator injectors tps sensor iac egr spark plugs ignition module)
As stated my 84 s10 v6 4.3 (it had an engine swap done to it ) is stalling ive already fixed fuel issues itll run ok for a few mins then stall out ive already done some test to see if it has a vacuum leak it does not. At least not that I can find
Brand new nozzle and I have ran all the calibrations but still getting prints like this what am I doing wrong here or what's going on with my printer
Hi i recently got a 84 s10 that had it engine swapped from an 88 s10 (only got it because it was in mint condition hardly any rust at all and because it had a 4.3 put in it) currently im having issues with it running rough when idling or stalling when hitting the brakes (somehow drove it home) not sure what's going on exactly. It does not appear to be a vacuum leak as every once in a while itll run ok when started. It also dies when hitting the brakes. Could this be caused by a possible failing iac??
Hi i recently got a 84 s10 that had its engine swapped from an 88 s10 (only got it because it was in mint condition hardly any rust at all and because it had a 4.3 put in it) currently im having issues with it running rough when idling or stalling when hitting the brakes (somehow drove it home) not sure what's going on exactly. It does not appear to be a vacuum leak as every once in a while itll run ok when started. It also dies when hitting the brakes. Could this be caused by a possible failing iac??
Issue is fixed accidentally use wrong nozzel
I recently acquired a kobra s1 for free replaced the nozzle but am having issues could my new nozzle be clogged again
• Printer Model: kobra s1
• Slicer :anycubic slicer next
• Filament material: pla brand creality
• Nozzle and bed temperature: nozzle :215 bed:65
• Print Speed: unsure still trying to understand a different anycubic slicer
Retraction settings :unsure still trying to understand a different anycubic slicer
Why do my prints keep coming out like this??? I've adjusted alot of settings but somehow still can't cant get my print to come out any better
Hi I recently bought a very cheap used kobra s1 that was missing a few parts. I ended up replacing the parts how when I got to do a print nothing sticks it's like it's not squishing it enough or it's moving to fast but im unfortunately not exactly sure what's going on. Ultimately I bought the 3d printer to replace my ender 3 v3 se simply because ive had to much issue with it. I was able to get a print to stick once but that was with some glue I dont wanna have to use glue all the time