Playing T10 on Lincoln. I'm healer. The 3 random dummies in my group charge the steps all the way to the top go inside and get downed instantly. NPCs now come after me...I had no chance!! Game over in less than 2 mins!!
Tokens gone! 😂
of course when the loot is half way decent.
​
Is that you can run just about any build unlike escalation. I've used Breaking point, ongoing Directive, Coco... Pretty much anything but the meta. It's nice change of pace
I last season I played escalation daily T10, probably completing it 99% of the time. This season.. I'm 2 for 3 and it's been tough. Do I need to fully complete the journey before grinding again? I know last season, escalation was tougher if you had not finished the journey or didn't have munitions
But this guy really thought I was going to let him play T10 using the following build. I thought he was trolling at first.. But he was serious.
That I played escalation with today. SHD levels ranged from 1200 to 20k. I hosted every game and we went 10 for 10 on tier 10 (Grand Washington Hotel). Some days, escalation pisses me off... Today was not one of those days!!
Trying to keep things interesting but using things other than TS and Striker.
It seems that the bleed damage does little on T10. I had to switch builds halfway through the run because my damage was low. (And I was the leader) Does anyone use OD in escalation T10?
I was playing escalation t10 (I was hosting).. Things were going normally. And then I saw a teammate go down... But he got up instantly!!! It was like a split second!! As we played, every time he went down, he almost got up instantly, except maybe one time. He wasn't using cover and at one point, it looked like he was chasing the NPCs.
He was. SHD 2000ish..I looked at his build after we were done and he had Quantum on everything and they were all leveled up. He said that quantum plus the prima donna was why he was pretty invincible.
Just finished with don't randoms District arena... With 3 mins left well still hadn't finished!!!! We wiped on the last boss. It was basically 2 dps, 1 healer and a trashcan!!
The trashcans build is attached. I wanted to quit so bad, but I didn't want to do the leader dirty. I can't believe this guy was level 8500... He just hung in the back doing zero damage. Beyond frustrated
My CC worked fine until I installed the Canvas system! After that, it became the most unlreliable of all my printers.
I think when I worked on it, I knocked the bed out of wack. My bed mess was off my 2.99mm. After adjusting, testing, etc. I got it to 0.700 mm.
Then it was time to run some 1st layer test to figure out if I need a z offset change. It needed .030.
I then calibrated my filaments and pressure advance. In the end, I probably spent about 6-7 hours getting the printer dialed in.
For those who have problems with their prints. Spend some time dialing it in. It's time consuming, but definitely worth the effort.
I was having a hard time always finding a healer while running t10, so I decided to put the dps down and create a healer build. Long story short...it was fun and chaotic trying to keep everyone alive. I went with FI with Birdies. Being able to do something other than dps was a breathe of fresh air. (SHD 2900)
Dude jumps in the game and I ask him does he have something with more DPS, he says he's "running with this" against my better judgement I start the game. It takes him forever ever to kill 1 enemy. Once we hit a break, I ask him "do you have something with more DPS?" He gets in his feelings and quit. Then we later wipe. I wasn't rude or nasty, but I knew we were going to have to carry him. I guess it's partly my fault for starting the game.
Is it me or is 10 easier without that stupid hotfoot? I was stuck in tier 6 purgatory for the longest time. I recently got dragged into a t10 match and did really well now that I don't have to keep moving constantly. I've played a few more times and it almost feels like I'm playing t6 or 7.
4 agents defending a location against multiple waves of enemies, each wave more difficult (like escalation tiers 1-10+) by the end your fighting hunters, chugus, aerial drones, etc, etc.
After reading the daily escalation post(thanks for posting that!) I've realize that I've barely used the available brand/gear sets (SHD 2800ish). Tipping Scales, Core, and HanaU are the ones I use primarily. I honestly don't even know how half of them work. Are there players who actively use 7+ different sets? I'm going to make it a point to start using different sets in open world.
I had 1000 hrs prior....and Ive had nothing but issues since. It seems like the bed is odd, but I've run the calibration a few times. My latest print looked like this after 2 layers.
Any ideas suggestions are appreciated. Im tempted to do a hard reset or install opencentauri
How many times have you run it so far?? I'm close to 30.
Just installed canvas.. And after fiddling with it for 2 days, it's printing correctly. But I've noticed an issue with the the filament sync.
When I load and set the filament as generic PLA and hit sync in elegoo slicer. It gets loaded into the slicer as Elegoo ABS. Anyone else seen this issue?
Just in case you missed it... they gave us a cache with 200 escalation tokens.
Ordered a 3 month supply, recieved it quickly and there was no issues... trying to reorder has been a nightmare. I can't reach anyone... I cant contact anyone via the portals, etc. So I decided to come here and all I see are issues. Is there anyone that has better customer service that these guys?