u/DudeGamerDario

As the title says, my Instagram account was wrongly disabled for "child sexual exploitation". when I had first found this out, I clicked the appeal button but now that's gone and says i can't do an automated appeal. Trying to contact instagram support is hell. the shitty ai doesnt even work on this account and when i tried on my other account under the same email, it did everything except show me how to appeal my account and refused to give me a support email or phone number. i've had this account for years and really would like for it to NOT be deleted. if anyone has advice please let me know. thank you!

has anyone had this issue before? i'm trying to install badupdate to my usb stick but i keep getting this error for like half a second then the builder crashing. if snyone has a fix it would be greatly appreciated, thank you!!

Anybody have a fix to this? Eddy NG setup complete but klipper still saying Z axis must be homed before probing when i try to home my printer advice would be hugely appreciated, thank you!!

Finally got my eddy duo NG working but i can't save my setup now, it gives me this error. ignore the z offset adjust it was just to test autosave after i tried fixing it. help on this would be greatly appreciated, thanks in advance!!

[include KAMP_Settings.cfg]

[include Line_Purge.cfg]

[stepper_x]

step_pin: PB13

dir_pin: !PB12

enable_pin: !PB14

microsteps: 16

rotation_distance: 40

endstop_pin: ^!PC0

position_endstop: 0

position_max: 377

homing_speed: 50

[tmc2209 stepper_x]

uart_pin: PC11

tx_pin: PC10

uart_address: 0

run_current: 1.6

hold_current: 0.500

#stealthchop_threshold: 120

stealthchop_threshold: 0

[stepper_y]

step_pin: PB10

dir_pin: !PB2

enable_pin: !PB11

microsteps: 16

rotation_distance: 40

endstop_pin: ^PC1

position_endstop: 360

position_max: 360

homing_speed: 50

[tmc2209 stepper_y]

uart_pin: PC11

tx_pin: PC10

uart_address: 2

run_current: 1.6

hold_current: 0.500

#stealthchop_threshold: 120

stealthchop_threshold: 0

[stepper_z]

step_pin: PB0

dir_pin: !PC5

enable_pin: !PB1

rotation_distance: 2

full_steps_per_rotation: 200

microsteps: 16

endstop_pin: probe:z_virtual_endstop

position_min: -5

position_max: 410

[safe_z_home]

home_xy_position: 175,175 # Change coordinates to the center of your print bed

#home_xy_position: 360,360

speed: 50

z_hop: 10 # Move up 10mm

z_hop_speed: 5

# ---------- Z Stepper ----------

# Creality 42-34, 0.8A peak RMS (per phase)

# -------------------------------

[tmc2209 stepper_z]

uart_pin: PC11

tx_pin: PC10

uart_address: 1

run_current: 0.800

hold_current: 0.500

stealthchop_threshold: 0

[extruder]

step_pin: PB3

dir_pin: PB4

enable_pin: !PD1

microsteps: 16

rotation_distance: 4.69

nozzle_diameter: 0.400

filament_diameter: 1.750

heater_pin: PC8

sensor_type: Generic 3950

sensor_pin: PA0

control: pid

pid_Kp: 26.213

pid_Ki: 1.304

pid_Kd: 131.721

min_temp: 0

max_temp: 320

max_extrude_only_distance: 1200

max_extrude_cross_section: 5

[filament_switch_sensor filament_sensor]

pause_on_runout: True

runout_gcode: FILAMENT_RUNOUT

event_delay: 3.0

pause_delay: 0.5

switch_pin: !PC15

[tmc2209 extruder]

uart_pin: PC11

tx_pin: PC10

uart_address: 3

run_current: 0.850

hold_current: 0.500

stealthchop_threshold: 120

[heater_bed]

heater_pin: PC9

sensor_type: ATC Semitec 104GT-2

sensor_pin: PC4

control: pid

pid_Kp: 54.027

pid_Ki: 0.770

pid_Kd: 948.182

min_temp: 0

max_temp: 110

[fan]

pin: PC7

# (FAN_1 on card.)

max_power: 1.0

shutdown_speed: 0.0

cycle_time: 0.010

hardware_pwm: False

kick_start_time: 0.100

off_below: 0.0

[heater_fan controller_fan]

pin: PC6

heater: heater_bed

heater_temp: 45.0

[heater_fan nozzle_cooling_fan]

pin: PB15

heater: extruder

[exclude_object]

[mcu]

serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_2B002C0003504E5238363120-if00

[printer]

kinematics: corexy

max_velocity: 800

max_accel: 10000

max_z_velocity: 5

max_z_accel: 1000

#[static_digital_output usb_pullup_enable]

#pins: !PC13

[mcu eddy]

# FOR USB: replace this with your serial port ID

# FOR CANBUS: replace this with your canbus UUID

serial: /dev/serial/by-id/usb-Klipper_rp2040_504434040843CD1C-if00

restart_method: command

[probe_eddy_ng btt_eddy]

sensor_type: btt_eddy

i2c_mcu: eddy

i2c_bus: i2c0f

x_offset: -29

y_offset: -17

write_every_tap_plot: True

[temperature_sensor btt_eddy_mcu]

sensor_type: temperature_mcu

sensor_mcu: eddy

min_temp: 10

max_temp: 100

[temperature_sensor btt_eddy]

sensor_type: Generic 3950

sensor_pin: eddy:gpio26

[screws_tilt_adjust]

screw1: 35,103

screw1_name: front_left

screw2: 329,103

screw2_name: front_right

screw3: 35,360

screw3_name: back_left

screw4: 329,360

screw4_name: back_right

# Additional bed leveling screws. At least two screws must be

# defined.

horizontal_move_z: 5.

speed: 150.

screw_thread: CW-M4

[bed_mesh]

speed: 200

horizontal_move_z: 6

mesh_min: 50,50

mesh_max: 310,310

probe_count: 6,6

#fade_start: 1.0

#mesh_pps: 2,2

[gcode_macro G29]

gcode:

BED_MESH_CALIBRATE ADAPTIVE=1

[safe_z_home]

home_xy_position: 175,175

speed: 100.0

z_hop: 10.0

z_hop_speed: 5.0

[board_pins]

aliases:

# EXP1 header

EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,

EXP1_2=PA15, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PD6, EXP1_10=<5V>

[mcu CB1]

serial: /tmp/klipper_host_mcu

[resonance_tester]

accel_chip: adxl345

probe_points:

100, 100, 20 #an example

[adxl345]

cs_pin: CB1:None

spi_bus: spidev1.1

axes_map: z,y,-x # Modify according to the actual orientation of the ADXL345installed on the printer.

#[display]

#lcd_type: st7920

#cs_pin: EXP1_7

#sclk_pin: EXP1_6

#sid_pin: EXP1_8

#encoder_pins: ^EXP1_5, ^EXP1_3

#click_pin: ^!EXP1_2

#kill_pin: ^!EXP2_8

#[neopixel my_neopixel]

#pin: PA8

#chain_count: 8

#[temperature_sensor raspberry_pi]

#sensor_type: temperature_host

#min_temp: 10

#max_temp: 100

#[gcode_macro LED_OFF]

#gcode:

# SET_LED LED=my_neopixel RED=0 GREEN=0 BLUE=0

#[gcode_macro LED_HEATING]

#gcode:

#SET_LED LED=my_neopixel RED=1.0 GREEN=0 BLUE=0

#[gcode_macro LED_PRINTING]

#gcode:

#SET_LED LED=my_neopixel RED=1.0 GREEN=1.0 BLUE=1.0

#[gcode_macro LED_COOLING]

#gcode:

#SET_LED LED=my_neopixel RED=0 GREEN=1.0 BLUE=0

# See the sample-lcd.cfg file for definitions of common LCD displays.

[virtual_sdcard]

path: ~/printer_E5P_data/gcodes

[pause_resume]

[display_status]

[gcode_macro CANCEL_PRINT]

description: Cancel the actual running print

rename_existing: CANCEL_PRINT_BASE

gcode:

TURN_OFF_HEATERS

CANCEL_PRINT_BASE

G91

G1 z50 F600

G90

[gcode_macro PAUSE]

description: Pause the actual running print

rename_existing: PAUSE_BASE

# change this if you need more or less extrusion

variable_extrude: 1.0

gcode:

##### read E from pause macro #####

{% set E = printer["gcode_macro PAUSE"].extrude|float %}

##### set park positon for x and y #####

# default is your max posion from your printer.cfg

{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}

{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}

##### calculate save lift position #####

{% set max_z = printer.toolhead.axis_maximum.z|float %}

{% set act_z = printer.toolhead.position.z|float %}

{% if act_z < (max_z - 2.0) %}

{% set z_safe = 2.0 %}

{% else %}

{% set z_safe = max_z - act_z %}

{% endif %}

##### end of definitions #####

PAUSE_BASE

G91

{% if printer.extruder.can_extrude|lower == 'true' %}

G1 E-{E} F2100

{% else %}

{action_respond_info("Extruder not hot enough")}

{% endif %}

{% if "xyz" in printer.toolhead.homed_axes %}

G1 Z{z_safe} F900

G90

G1 X{x_park} Y{y_park} F6000

{% else %}

{action_respond_info("Printer not homed")}

{% endif %}

[gcode_macro RESUME]

description: Resume the actual running print

rename_existing: RESUME_BASE

gcode:

##### read E from pause macro #####

{% set E = printer["gcode_macro PAUSE"].extrude|float %}

#### get VELOCITY parameter if specified ####

{% if 'VELOCITY' in params|upper %}

{% set get_params = ('VELOCITY=' + params.VELOCITY) %}

{%else %}

{% set get_params = "" %}

{% endif %}

##### end of definitions #####

{% if printer.extruder.can_extrude|lower == 'true' %}

G91

G1 E{E} F2100

{% else %}

{action_respond_info("Extruder not hot enough")}

{% endif %}

RESUME_BASE {get_params}

######################################################################

# Start Print and End Print

######################################################################

[gcode_macro START_PRINT]

gcode:

{% set BED_TEMP = params.BED_TEMP|default(80)|float %}

{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(160)|float %}

# Bed temp

M140 S80

# Extruder preheat 160

M104 S160

# Home the printer

G90

M83

G28

# Preheat the bed

M140 S{BED_TEMP}

M190 S{BED_TEMP}

# Adaptive Mesh sequence

BED_MESH_CALIBRATE PROFILE=adaptive ADAPTIVE=1

#Parking head for final heat

Smart_Park

#FINAL HEAT

M104 S{EXTRUDER_TEMP}

M109 S{EXTRUDER_TEMP}

#ADAPTIVE PURGE

LINE_PURGE

[gcode_macro END_PRINT]

gcode:

G1 E-5 F100

#LED_COOLING

# Turn off bed, extruder, and fan

M140 S0

M104 S0

M106 S0

# Move nozzle away from print while retracting

G91

G1 X-2 Y-2 E-3 F300

# Raise nozzle by 10mm

G1 Z10 F3000

G90

# Disable steppers

M84

######################################################################

# Filament Change

######################################################################

# M600: Filament Change. This macro will pause the printer, move the

# tool to the change position, and retract the filament 50mm. Adjust

# the retraction settings for your own extruder. After filament has

# been changed, the print can be resumed from its previous position

# with the "RESUME" gcode.

[pause_resume]

[gcode_macro M600]

gcode:

{% set X = params.X|default(50)|float %}

{% set Y = params.Y|default(0)|float %}

{% set Z = params.Z|default(10)|float %}

SAVE_GCODE_STATE NAME=M600_state

PAUSE

G91

G1 E-.8 F2700

G1 Z{Z}

G90

G1 X{X} Y{Y} F3000

G91

G1 E-50 F1000

RESTORE_GCODE_STATE NAME=M600_state

# Enable arcs support

[gcode_arcs]

resolution: 0.1

[gcode_macro TEST_SPEED]

# Home, get position, throw around toolhead, home again.

# If MCU stepper positions (first line in GET_POSITION) are greater than a full step different (your number of microsteps), then skipping occured.

# We only measure to a full step to accomodate for endstop variance.

# Example: TEST_SPEED SPEED=300 ACCEL=5000 ITERATIONS=10

description: Test for max speed and acceleration parameters for the printer. Procedure: Home -> ReadPositionFromMCU -> MovesToolhead@Vel&Accel -> Home -> ReadPositionfromMCU

gcode:

# Speed

{% set speed = params.SPEED|default(printer.configfile.settings.printer.max_velocity)|int %}

# Iterations

{% set iterations = params.ITERATIONS|default(5)|int %}

# Acceleration

{% set accel = params.ACCEL|default(printer.configfile.settings.printer.max_accel)|int %}

# Minimum Cruise Ratio

{% set min_cruise_ratio = params.MIN_CRUISE_RATIO|default(0.5)|float %}

# Bounding inset for large pattern (helps prevent slamming the toolhead into the sides after small skips, and helps to account for machines with imperfectly set dimensions)

{% set bound = params.BOUND|default(20)|int %}

# Size for small pattern box

{% set smallpatternsize = SMALLPATTERNSIZE|default(20)|int %}

# Large pattern

# Max positions, inset by BOUND

{% set x_min = printer.toolhead.axis_minimum.x %}

{% if x_min < 0 %}

{% set x_min = 0 %}

{% endif %}

{% set y_min = printer.toolhead.axis_minimum.y %}

{% if y_min < 0 %}

{% set y_min = 0 %}

{% endif %}

{% set x_min = x_min + bound %}

{% set x_max = printer.toolhead.axis_maximum.x - bound %}

{% set y_min = y_min + bound %}

{% set y_max = printer.toolhead.axis_maximum.y - bound %}

# Small pattern at center

# Find X/Y center point

{% set x_center = (printer.toolhead.axis_minimum.x|float + printer.toolhead.axis_maximum.x|float ) / 2 %}

{% set y_center = (printer.toolhead.axis_minimum.y|float + printer.toolhead.axis_maximum.y|float ) / 2 %}

# Set small pattern box around center point

{% set x_center_min = x_center - (smallpatternsize/2) %}

{% set x_center_max = x_center + (smallpatternsize/2) %}

{% set y_center_min = y_center - (smallpatternsize/2) %}

{% set y_center_max = y_center + (smallpatternsize/2) %}

# Save current gcode state (absolute/relative, etc)

SAVE_GCODE_STATE NAME=TEST_SPEED

# Output parameters to g-code terminal

{ action_respond_info("TEST_SPEED: starting %d iterations at speed %d, accel %d" % (iterations, speed, accel)) }

# Home and get position for comparison later:

M400 # Finish moves - https://github.com/AndrewEllis93/Print-Tuning-Guide/issues/66

G28

# QGL if not already QGLd (only if QGL section exists in config)

{% if printer.configfile.settings.quad_gantry_level %}

{% if printer.quad_gantry_level.applied == False %}

QUAD_GANTRY_LEVEL

G28 Z

{% endif %}

{% endif %}

# Move 50mm away from max position and home again (to help with hall effect endstop accuracy - https://github.com/AndrewEllis93/Print-Tuning-Guide/issues/24)

G90

G1 X{printer.toolhead.axis_maximum.x-50} Y{printer.toolhead.axis_maximum.y-50} F{30*60}

M400 # Finish moves - https://github.com/AndrewEllis93/Print-Tuning-Guide/issues/66

G28 X Y

G0 X{printer.toolhead.axis_maximum.x-1} Y{printer.toolhead.axis_maximum.y-1} F{30*60}

G4 P1000

GET_POSITION

# Go to starting position

G0 X{x_min} Y{y_min} Z{bound + 10} F{speed*60}

# Set new limits

{% if printer.configfile.settings.printer.minimum_cruise_ratio is defined %}

SET_VELOCITY_LIMIT VELOCITY={speed} ACCEL={accel} MINIMUM_CRUISE_RATIO={min_cruise_ratio}

{% else %}

SET_VELOCITY_LIMIT VELOCITY={speed} ACCEL={accel} ACCEL_TO_DECEL={accel / 2}

{% endif %}

{% for i in range(iterations) %}

# Large pattern diagonals

G0 X{x_min} Y{y_min} F{speed*60}

G0 X{x_max} Y{y_max} F{speed*60}

G0 X{x_min} Y{y_min} F{speed*60}

G0 X{x_max} Y{y_min} F{speed*60}

G0 X{x_min} Y{y_max} F{speed*60}

G0 X{x_max} Y{y_min} F{speed*60}

# Large pattern box

G0 X{x_min} Y{y_min} F{speed*60}

G0 X{x_min} Y{y_max} F{speed*60}

G0 X{x_max} Y{y_max} F{speed*60}

G0 X{x_max} Y{y_min} F{speed*60}

# Small pattern diagonals

G0 X{x_center_min} Y{y_center_min} F{speed*60}

G0 X{x_center_max} Y{y_center_max} F{speed*60}

G0 X{x_center_min} Y{y_center_min} F{speed*60}

G0 X{x_center_max} Y{y_center_min} F{speed*60}

G0 X{x_center_min} Y{y_center_max} F{speed*60}

G0 X{x_center_max} Y{y_center_min} F{speed*60}

# Small pattern box

G0 X{x_center_min} Y{y_center_min} F{speed*60}

G0 X{x_center_min} Y{y_center_max} F{speed*60}

G0 X{x_center_max} Y{y_center_max} F{speed*60}

G0 X{x_center_max} Y{y_center_min} F{speed*60}

{% endfor %}

# Restore max speed/accel/accel_to_decel to their configured values

{% if printer.configfile.settings.printer.minimum_cruise_ratio is defined %}

SET_VELOCITY_LIMIT VELOCITY={printer.configfile.settings.printer.max_velocity} ACCEL={printer.configfile.settings.printer.max_accel} MINIMUM_CRUISE_RATIO={printer.configfile.settings.printer.minimum_cruise_ratio}

{% else %}

SET_VELOCITY_LIMIT VELOCITY={printer.configfile.settings.printer.max_velocity} ACCEL={printer.configfile.settings.printer.max_accel} ACCEL_TO_DECEL={printer.configfile.settings.printer.max_accel_to_decel}

{% endif %}

# Re-home and get position again for comparison:

M400 # Finish moves - https://github.com/AndrewEllis93/Print-Tuning-Guide/issues/66

G28 # This is a full G28 to fix an issue with CoreXZ - https://github.com/AndrewEllis93/Print-Tuning-Guide/issues/12

# Go to XY home positions (in case your homing override leaves it elsewhere)

G90

G0 X{printer.toolhead.axis_maximum.x-1} Y{printer.toolhead.axis_maximum.y-1} F{30*60}

#*# <---------------------- SAVE_CONFIG ---------------------->

I (THINK) i followed all the steps on the github, but end up with this error each time. no luck installing with the alternate way though cmd either. help would be greatly appreciated! thank you!

Hey guys! my dream machine's tape player doesn't play properly, but it does only if the play button is pushed down harder while it's already playing. has anyone experienced this issue on their tape deck before/is there any fix to this? thank you!!