Always liked this photo but hated the single funnel so fixed it and has been my desktop for ages. Thought I would share. Not 100% accurate but the darkness mostly hides my sins. She did not look right without the front funnel. Done the old fashioned way of trial and error, no AI here.
My fridge has been in storage for three years due to moving out of state. When I originally purchased this fridge ridiculously cheap, it suffered from damaged wires in the deli drawer that I fixed and one of the door closed switches somehow managed to get unplugged. Everything worked fine when I unplugged it. Finally have it in a new home and it’s cooling but not cold. Fridge is around 50 but freezer is warmer and after so long the fridge sudden thinks there was a power outage with a beep and PO on the display. Deli drawer is currently disconnected because I needed to replace it as the original was lost during my move and the one I found suffered from water ingress. Not a big deal. Icemaker has been turned off because I currently do not have a supply hose installed. Lights work, dispenser does make sounds when I press the paddle for ice or water. All functions on the panel seem to work normally. What can I look at for a possible issue? I was not pleased with my appliance movers but that’s sort of a moot point now. Any suggestions welcome.
My fridge has been in storage for three years due to moving out of state. When I originally purchased this fridge ridiculously cheap, it suffered from damaged wires in the deli drawer that I fixed and one of the door closed switches somehow managed to get unplugged. Everything worked fine when I unplugged it. Finally have it in a new home and it’s cooling but not cold. Fridge is around 50 but freezer is warmer and after so long the fridge sudden thinks there was a power outage with a beep and PO on the display. Deli drawer is currently disconnected because I needed to replace it as the original was lost during my move and the one I found suffered from water ingress. Not a big deal. Icemaker has been turned off because I currently do not have a supply hose installed. Lights work, dispenser does make sounds when I press the paddle for ice or water. All functions on the panel seem to work normally. What can I look at for a possible issue? I was not pleased with my appliance movers but that’s sort of a moot point now. Any suggestions welcome.
Watching Louis Rossmann last night during his Verizon video, he mentioned having extra Blackberry screens while going through some old stuff in his store. Perhaps someone near him in TX might want to reach out and get them before he tosses them.
Watching Louis Rossmann last night during his Verizon video, he mentioned having extra Blackberry screens while going through some old stuff in his store. Perhaps someone near him in TX might want to reach out and get them before he tosses them.
What is the logic of removing office classic but Skype is still OK? Everyone in the office hates the modern outlook and will clutch the classic version until pulled from their cold dead SSDs.
GW has been overall lame of late and for 3D even worse, but finally some results. The Space station one - though a bit dated - is the only one I’ve watched so far and except for the first few minutes faking me out that were not in 3D, is excellent. Now I need to find the first Narnia movie.
So far the transition to the new router has been relatively painless, but two issues. I wanted to put the clients IP phones on the IoT network but I do not see any way to connect the wired IP phone device to the IOT network. Am I missing something or this box will not do that. Secondly I wanted to add a printer on the production network on the guest. I was able to do that using the EAP245 access points we were using on the old system and create a cut through just for the printer. I don't see a way to do that on the new router. I could kill the guest network on the CR1000A and move it to the EAPs but that seems a pain and the client isn't thrilled to have to get a printer just for the guest network. Looking for some input.
Still sealed deck among other travel playing cards. Made in England printed on the flaps. Cunard Line on the reverse of the box. In very good shape for its age.