Cant flash klipper on BTT SKR 1.4 TURBO
I can seem to flash klipper on my new skr 1.4 . Any ideas would help lots
Rasberry pi 4
8gb micro sd card
u/gjackc — 21 hours ago
u/gjackc
r/FixMyPrint r/3DprintingHelp r/ender3 r/3Dprinting r/MarlinFirmware r/klippers r/ender3v2 r/BIGTREETECH
▲ 8 r/ender3v2
Is it still and ender ?
Is it still an ender 3 v2 even with these upgrades?
Been upgrading my ender lots still more to come but here are the upgrades. The black cases i designed my self in fusion 360
Pei bed
Silicone Springs
Linnear rails for y
Duel z
Bltouch
Hotend:
Tze3 2.0
Direct drive
Board:
Btt skr 1.4 turbo
Rasberry pi 4
More to come
Replace direct drive with the orbiter extruder
Linear x rails
u/gjackc — 3 days ago
▲ 2 r/klippers
Installing Input shaper libatlas-base-dev' has no installation candidate
new to klipper
cant figure out why its not working
ender 3 v2
raspberry pi 4
using putty to install input shaper
accelerometer FYSETC (Portable Input Shaper)
https://www.klipper3d.org/Measuring_Resonances.html#software-installation
u/gjackc — 19 days ago
▲ 1 r/FixMyPrint
Z axis shifting
Getting this y shifting
Ender 3 v2
Klipper
Orca
.4
Pla 200
Bed 60
What ive done
Tighten the belt
Replace the motor
Slowed print speed down
Sounds
A harsh vibration sound from the motor
I could replace the belts as Ive had the printer in 2019
u/gjackc — 29 days ago
▲ 1 r/klippers
trouble installing inputshaper
ender3v2@ender3v2:~ $ ~/klippy-env/bin/pip install -v numpy
Using pip 25.1.1 from /home/ender3v2/klippy-env/lib/python3.13/site-packages/pip (python 3.13)
Looking in indexes: https://pypi.org/simple, https://www.piwheels.org/simple
Requirement already satisfied: numpy in ./klippy-env/lib/python3.13/site-package s (2.4.4)
ender3v2@ender3v2:~ $ sudo apt install python-numpy python-matplotlib
Package python-numpy is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source
Error: Package 'python-numpy' has no installation candidate
Error: Unable to locate package python-matplotlib
ender3v2@ender3v2:~ $ ^C
ender3v2@ender3v2:~ $ ~/klippy-env/bin/pip install -v numpy
Using pip 25.1.1 from /home/ender3v2/klippy-env/lib/python3.13/site-packages/pip (python 3.13)
Looking in indexes: https://pypi.org/simple, https://www.piwheels.org/simple
Requirement already satisfied: numpy in ./klippy-env/lib/python3.13/site-package s (2.4.4)
ender3v2@ender3v2:~ $ ^C
ender3v2@ender3v2:~ $ sudo apt install python-numpy python-matplotlib
Reading package lists... 0%
Package python-numpy is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source
new to klipper
cant figure out why its not working
ender 3 v2
raspberry pi 4
using putty to install input shaper
accelerometer FYSETC (Portable Input Shaper)
u/gjackc — 1 month ago
▲ 11 r/ender3v2
DIY air filter carbon pallets
Looking to make a DIY air filter i found that the filters from what ive seen is expensive. Will these pallets work for just air ?
Open to any other alternative and suggestions
u/gjackc — 1 month ago
Orbiter v2 install not feeding filament
Ender 3 v2
Klipper
Hotend isint clogged as ive tested manually feeding filament
Orbiter v2 extruder is pulsing not extruding
u/gjackc — 2 months ago
Klipper and Orca
I've been upgrading my printer for a couple months now and I'm impressed . Stock hotends soon to ave the tze3 3.0 hotends . Main things was software I got a Raspberry pi 4 klipper and moved from Cura to Orca and the speeds have gotten faster each software change . Still in the learning phase but oh my this is awsome results
u/gjackc — 2 months ago
▲ 2 r/klippers
WIFI Connection issue
Im quite new to klipper
my understanding is that when the wifi is turned off the rasberry pi loses its IP adress and i need to re flash the sd card.
is there an easy way for the wifi to remember the rasberry pi or vice verca ?
u/gjackc — 2 months ago
New to klipper needing help for setup
Pla
Nozzle 210
Bed 60
Ender 3 v2
Raspberry pi 4 4gb
Cura as a slicer
u/gjackc — 3 months ago
▲ 1 r/klippers
Ender 3 v2 Newbie to Klipper
any good videos for Klipper install I'm struggling on how to do it
Printer: Ender 3 v2 orignal motherboard
Raspberry pi 4 4gb
micro sd 64gb x1 32gb x1 A1
u/gjackc — 3 months ago
▲ 1 r/ender3v2
Upgrading my ender 3 v2 Hot end
looking around for a good hot end just a fun thing to upgrade .I'm open to suggestions in what is good and what is bad
Mainly printing PLA 220c
Future plan is Upgrading:
Motherboard To BIGTREETECH BTT SKR V1.4 Need help with what's a good motherboard too :D
Installing raspberry Pi looking at getting a Pi4
u/gjackc — 3 months ago
▲ 2 r/ender3v2
Is this heat creep
Just sorting out my printer just need better option on if it ia so
u/gjackc — 3 months ago