For those who were asking me about the range he is it in gaming action. I usually shoot just paper but the games are fun as well. This is a simple game but zombies always takes the cake. Gun in fusion xp comp

Alright so after watching, this video angle is trash aha. But you get the gist. Idk is the built out C2 is worth the extra squeeze. Don't get me wrong, I love my c2. On the other hand this fusion can hold its own. Granted its a full steel gun but i dont have a xc to compare it to, or any other steel island comp gun.

Have a couple ported 2011's done up by vulcan and was wandering what a good range ammo that wont break the bank and does well with ports. All I know is blazer brass is no go. But what is decent?

Same gun you always see but I adjusted the gass from 28 notches closed up to 23. Its seems more reliable now. I think a good middle ground between the two will be perfect.

Breakdown: sam7r milled, 3pos frt, kns adj gas, slr handguard, deadair wolverine.

I recently posted with issue with my xp comp not going fully into battery. I reached to fusion and they sent a whole kit with 4 springs and a "tuned" extractor. I ended up tuning my own prior to its arrival and it seemed to work well. Im still going to tune the sear spring for a crisper pull but its nice and running well now.

Closed the gas off a little to much but wanted to see how slow i can get the ROF and still function. Home grown 3 pos frt.

Took the xp to the range yesterday and was pleasantly surprised on its flatness and ease of shooting. Trigger is nice, but cook be tuned a bit. The weight makes it return fast though. It wasn't without its fair share of hiccups. The slide did not go fully into to battery numerous times. I know everyone says to change to 10# or 9# spring but I had to see if my was one in a million. Also had one dead trigger ill post the video attached down below.

Just picked this up today after watching every YouTube review. Time to burn her down with some lead. See if the rumors of 90% of the xc is true

Same old mac just another post. Ps this has factory ejector and factory locking piece. Runs flawless with it. Did not cycle with 80° or 90°

This is a c2 with a p grip with vulcan reverse crown and ignis ports. Trigger was tuned to 2 pounds with reddirt shoe and I believe 11pound recoil springs

So I switch out the 90°block for the factory one. I know they say its not recommended because of roller dents. Haven't seen em yet. But this thibg is eating everything now. Will be sbr soon.

Tuned the gas with kns to make this thing not have horrible trigger slap anymore. Runs great now I just have to notch the reciever. P.s aks will make you bleed lol. If your gunna run a can with frt, get a kns!

Just removed the rivet on the arsenal sam7r and installed a kns piston. I started with a spring loaded center punch tool the 1/16" bit halfway through then went to 1/8" about a 1/4 way through. Then took a 3/32 punch and gave her the beans for about 10 swings. Easy easy. P.s sacrifice a punch and a drill bit in doing this

I swapped out my mac mags a a couple hk mags. Seems to work great. Also I did change back to factory locking piece i had issues running the 90 I got an 80° that i didn't even try. This b&t can is a flow through so I think there isn't enough gas with those. Only ran 115 with of locking piece and hk mags so far with post again with 147. P.s took off handstop after everyone said it was gay lol

Gun mag warehouse has these tan HK mags available on sale i think they were 65 i can remember

Here is the sam7 with 3 position. I have not cut the receiver for the 3rd position yet just wanted to test first so you can see it falling. But it works.

I posted on your earlier about the same thing and I think I got it to work now. It seems to be good in all 3 positions as far as I can.Tell. I have not cut a groove into the receiver yet.Because I'm still trying to see exactly where.To put it for the indent in the safety selector. I think I'm going to cut the , and then I will test fire. Also found that the amount of pressure you put on the trigger really plays a big role in this. Let me know what you guys think or have any input..

Got this thing in a while back. I shot it about two boxes worth. It seemed sluggish to cycle the bolt. I used that blue box in Pic. Does anyone know what causes this? Should I run 100 rounds of buck first?

Here's my a3s-sd at home set up. This things has never failed me yet. Running 124 i believe right here at some steel at 50 yards. Hoping someone releases a true SD barrel for the stribog soon. If any out there let me know.