u/Advanced-File6434

what i do wrong

The Bug: After any reboot, the 2.4GHz speed hard-caps at 1-2 Mbps. The web UI settings do not visibly change-it still shows my configured AX/Wi-Fi 6 settings-but the actual performance tanks. 5GHz is unaffected. Farmware version is AOT5221ZYR2.28 The Workaround: I have to log into the web UI, change the 2.4GHz standard to b, apply, and then change it back to ax. This restores full speed until the next reboot. What I Tried: Edited config.xml to permanently fix the initialization. Tried forcing (ax, n,ax, bgnax), locked 20MHz, and disabled PMF/DFS/Bandwidth Coexistence. Nothing prevents the post-reboot speed drop. Has anyone found a permanent fix, or should I demand a different router model?

Where is the 'Patch bundles' category located so I can delete a saved bundle? I only see the 'Saved APK' section, but the storage graph shows that 'Patch bundles' is taking up 210 MB. How do I clear those?

I have an AOT5221ZY fiber router, but after completing the configuration, Zoiper still doesn't show a green signal. The XML file only contains IPv6 data, and even after modifying it, neither Zoiper nor any other SIP softphone works. What should I do to solve this issue?

am troubleshooting a standard 2.1 channel audio amplifier board (12-0-12 dual-rail, TDA2030s for satellites, D2050 for the subwoofer, F4558 crossover). It suddenly developed a loud, constant hum on the subwoofer channel that does not change intensity when adjusting the volume.

​If the speaker is disconnected, the chip gets hot, but the moment a 4-ohm speaker is connected, the IC pulls massive current and gets blisteringly hot almost instantly.

​Diagnostic Tests i do

​Power Rail Check: Measured across Pin 3 (-Vcc) and Pin 5 (+Vcc) on the subwoofer IC. Getting a healthy ~30V total swing (roughly -15V and +15V). Main 1000µF 25V filter capacitors show no visual signs of bulging or leaking.

​DC Offset Test: Measured between Pin 3 (-Vcc) and Pin 4 (Output) on the original D2050 and got exactly 15V. This confirms Pin 4 is sitting at 0V relative to the main ground, so there is no direct DC short to the rails.

​IC Swap: To rule out internal failure or oscillation inside the D2050, I completely desoldered it and swapped in a spare UTC2030A (properly isolated with a thermal pad on the heatsink).

​Swap Result: The exact same symptoms persisted with the new IC. It produces the same heavy hum and instantly overheats when the speaker is connected.

Please guide me what i do next

Whenever I run a speed test on my 2.4 GHz band, I only get 1 to 2 Mbps download, though the upload speed is fine. On the 5 GHz band, I get full speed for both downloads and uploads, but its coverage is very limited. Is there any way to get full speed on the 2.4 GHz band without buying an external mesh router or extra equipment?

Hey everyone, hoping you can help me out with a headache of a board today.

It completely refuses to power on. The frustrating part is that there’s no magic smoke, no burn marks, and visually, everything looks absolutely pristine.

I scratched off a tiny bit of the green solder mask right next to the DC barrel jack to get a good probe on the bare copper. My multimeter is just screaming at me in continuity mode—I've got a dead, solid short between the main power rail and ground.

I probed the main input protection diode (D7, an SS14). In-circuit, it's reading about 145 one way, and 1445 the other way.

so what i do and how to fix this issue.....

Thanks!

like beyond the dns at more deep level

because my cpu and ram are lying all the time so i want to full utilise this hardware and bypass all airtel restrictions.

Is there is some one that does this ......

it show me this even when i enable Bypass image region restrictions.

😭😢

Wtf is Meta thinking? They are officially trying to push a new subscription model for WhatsApp, and it's ridiculous. If you look at the screenshot I attached , they are asking for ₹79.00/month just to unlock features that shouldn't be premium in the first place.

I hope morphe releases patch for WhatsApp..

I've been using the Tablet UI on my phone, and honestly, I like it much more than the original mobile layout.

The larger video thumbnails, cleaner interface, and overall viewing experience feel much better to me. It makes browsing YouTube more enjoyable, even if it leaves a little extra spacing between videos.

Whenever I click a YouTube chat/message link , I get this error:

«"Messaging on YouTube isn't available in your country."»

This happens every time I try to open a chat link.

Has anyone else experienced this? Is there any setting, hidden toggle, or feature in MorpheApp that can bypass this restriction, or is this completely controlled by YouTube?

Any help or suggestions would be appreciated.