u/SuperJonesy408

First off, I don’t know if they are monitoring this sub but here goes:

AF is producing good pistols at a great value. My Romulus is matte black but that DLC coating is sexy and super slippery. The grip upgrade is a major win for AF and the consumer.

I’ve shot a friend’s MAC 9 DS Comp and my Romulus was better BEFORE the grip upgrade. Now there is no comparison. I have about 2000 rounds through mine and now I plan to do an ignition kit now and continue to shoot the beans out of it

Comparatively priced pistols like the MAC DS 9 Comp and the Kimber Warrior better watch out.

I am looking for the part number to order some recoil lugs to run a Vortex Defender XL on my P211 and P226. Both pistols were ordered without an optic installed.

I've dug into the Sig website but I don't see them anywhere. I tried calling Sig a few weeks back and the rep seemed like he was passing the buck to Vortex for them not including it. I don't mind ordering them, I just need a part number.

Thanks for your help.

edit: I think I may have tossed them when I threw out all the promo materials in the box.

Edit: I had to use some stones to take a few thousandths off the top and bottom of the trigger shoe to get it fitted. Took a few minutes but it works flawlessly now. Credit to u/skwmd375 for the details.

Hey folks,

I just spent a few hours fitting my AF Aluminum Grip to my Romulus and I thought I was going crazy. The grip safety kept binding and the trigger, hammer and sear linkage was funky. It would not pass functions check. The grip safety would get pinned, the hammer would fall and when cocked back it would fall on its own.

After disassembling and reassembling the action a few times I took it down to just the grip. I noticed the Red Dirt Trigger was binding in the grip somewhat.

So I took my old AF trigger out of my drawer and got some calipers out. The RD trigger bar is a few thousandths wider and the trigger shoe is a few thousandths taller. Without modifying the grip or trigger it would not work. I dropped in the AF trigger, reassembled with no issues and it is buttery smooth.

Hope this helps save someone else a few hours of their evening.

I have two form1 lowers, both approved and engraved. My form1 for both says Caliber 5.56mm with barrel of 11.5"

I have a 8" Banshee 9mm Upper. Am I legal running this upper on the form1 lower?

(I wish we could form1 Caliber "MULTI" like it says on the lower)

I've been sending it as my local ranges don't care, but I want to be in full compliance with the law.

I have a CMMG Banshee 9mm and the width of the buffer spring retaining pin channel on the BCG is 0.1860 inches. I believe triggers like the Atrius are too thin to work with this BCG so I'd like to find something that bridges the channel in the BCG.

I know the RareBreed trigger reset lever is 0.2535 inches wide and will work with the Banshee BCG. However, I refuse to support them.

I'm told the Partisan Disruptor might work but I don't have a measurement for the reset lever. If anyone knows the width of the reset lever please post it.

If you have any other trigger with a reset lever 0.25 inches or wider please let me know.

Hey folks,

I shoot NRL22 and I have a quick question. The following is an imaginary outlaw stage that I'm using to illustrate my question:

40 yards: 1/4", 1/2", 3/4" on a KYL rack

100 yards: 1.5" & 2" on a double hanger

1. KYL Largest, Far Large, KYL Middle, Far Small
2. KYL Small, Far Large, KYL Large, Far Small
3. KYL Middle, Far Large, KYL Small, Far Small

6 shots on KYL, 6 shots on Far. Dope says 0.16 MIL down for KYL, 1.78 MIL up for Far. Difference in elevation is 1.94.

Should I dial 0.2 down for KYL (My zero-stop is at 0.3 down) and just hold 2 up (0.2 down + 1.78up) for Far? Is my understanding correct? If not, please advise.

Thanks for your contribution and expertise.

edit: Fixed my stupidity.

I live in the Midwest so I'm searching for matches in my state and surrounding states because it do be like that. The list of states is absolutely stupid. Not listed alphabetically, some are by name and some by abbreviation. Missouri is listed as "MO" and "Missouri".

It's an absolute mess that a first year web developer could design better.

Thank you for coming to my TED talk.

I shoot NRL22 and my current scope is an Athlon Cronus BTR Gen2 4.5-29x56. Got some feedback from other shooters the Cronus has pretty poor parallax adjustment inside 100. I found this out last match.

One stage was 1/4" and 1/2" at 36 yards and 2.5" at 100 yards. The 100 was easy to dial parallax and hold elevation but switching from 36 to 100 to 36 was pretty rough. The only target that was sub MOA was the 1/4" but I had trouble with accuracy overall due to dialing parallax. Another stage was 59, 70 and 82 yards. Targets ranged from 1.6 to 2.3 MOA but again, parallax dialing bit me. Parallax was just.. off.

In general, there wasn't a lot of fine adjustment inside 100. There didn't seem to be a "good enough" solution to parallax to increase speed. It was either in focus or took too long to dial it. I timed out a few stages I'm looking for suggestions for the new season starting in May. Something with 15yd minimum with forgiving parallax and pretty fine adjustments. Big jumps just don't play well when switching between intermediate distances for NRL22.